BorMann PRO BAT5080 Mode D'emploi page 4

EN
Safety instructions
Please read these instructions carefully before attempting to assemble, install, operate or maintain the product described. Protect yourself and other people
by observing all safety information. Failure to comply with instructions could result in personal injury and/or property damage! Retain instructions for future
reference.
Unpacking
Before and after unpacking the package, inspect carefully for any damage that may have occurred during transit. Make sure fittings, bolts and so on are tight
before putting compressor into service.
WARNING!
Do not operate compressor if it have been damaged during shipping, handling or use. These damage may result in bursting and cause injury or
property damage.
DANGER!
Breathable Air Warning
This compressor is not equipped and should not be used "as is" to supply breathing quality air. For any application of air for human consumption, the air
compressor will need to be fitted with suitable in-line safety and alarm equipment. This additional equipment is necessary to properly filter and purify the air
to meet minimal specifications for Local Standard.
General safety information
Since the air compressor and other components (material pump, spray guns, filters, lubricators, hoses, etc.) used, make up a high pressure system, the
following safety precautions must be observed at all times:
1. Read all manuals included with this product carefully. Be thoroughly familiar with the controls and the proper use of the equipment.
2. Follow all local electrical and safety codes as well as in the US, National Electrical Codes (NEC) and Occupational safety and Health Act (OSHA).
3. Only persons well acquainted with these rules of safe operation should be allowed to use the compressor.
4. Keep visitors away and NEVER allow children in the work area.
5. Wear safety glasses and use hearing protection when operating the compressor.
6. This machine is not intended for domestic use.
7. Before each use, inspect compressed air system and electrical components for signs of damage, deterioration, weakness or leakage, repair or replace
defective items before using.
8. Check all fasteners at frequent intervals for proper tightness.
WARNING! Electric motors, electrical equipment and controls can cause ignition conditions in combination with the presence of flammable gases. Do not
use the machine and do not carry out any repair work while in the vicinity of flammable gases. Never store flammable liquids or gases near the compressor.
CAUTION! Compressor parts may be hot even if the unit is stopped.
9. Keep fingers away from a running compressor, fast moving and hot parts will cause injury and/or burns.
10. If the equipment should start to abnormally vibrate, STOP the engine/motor and check immediately for the cause, vibration is generally a warning of
trouble.
11. To reduce fire hazard, keep engine/motor exterior free of oil, solvent, or excessive grease.
WARNING! Never remove or attempt to adjust safety valve. Keep safety valve free from paint and other accumulations.
DANGER!
Never attempt to repair or modify a tank! Welding, drilling or any other modification will weaken the tank resulting in damage from rupture or explosion.
Always replace worn or damaged tanks.
WARNING! Drain liquid from tank daily.
13. Tanks rust from moisture build-up, which weakens the tank. Make sure to drain tank regularly and inspect periodically for unsafe conditions such as rust
formation and corrosion.
14. Fast moving air will stir up dust and debris, which may be harmful. Release air slowly when draining moisture or de-pressurizing the compressor system.
Spraying precautions
WARNING! Do not spray flammable materials in vicinity of open flame or near ignition sources including the compressor unit.
15. Do not smoke when spraying paint, insecticides, or other flammable substances.
16. Use a face mask/respirator when spraying and spray in a well ventilated area to prevent health and fire hazards.
17. Do not direct paint or spray other sprayed material at the compressor. Locate compressor as far away from the spraying area as possible to minimize
over-spray accumulation on the compressor.
18. To reduce fire hazard, Locate compressor far away wood cutter to avoid sawdust be sucked into motor.
19. When spraying or cleaning with solvents or toxic chemicals, follow the instructions provided by the chemical manufacturer.
Unpacking and assembly (Fig.1 - Fig.2)
Remove compressor from the carton (See Fig.1).
Carefully inspect the equipment for any missing items or damage incurred during transit.
If anything is found to be missing or damaged contact your nearest BORMANN Dealer.
We recommend that you store the packaging for the duration of the warranty period. If necessary, it will be easier to
return the compressor to the service centre.
Fit the wheels (See Fig.2) and front feet.
Confirm that the mains voltage corresponds with the voltage shown on the compressor's data/specification plate.
4
WWW.NIKOLAOUTOOLS.COM
Fig. 1
Fig. 2