Publicité
Les langues disponibles
Les langues disponibles
Impact Time
Tool will automatically shut off after impacting for a specific
time limit set by the user in the Tool Connect™ app.
Precision Tap™
CAUTION: Use only impact-rated taps
and accessories.
CAUTION: Tapping not recommended for use on
critical or precision workpieces.
CAUTION: Tap life is heavily affected by tool
alignment with the workpiece, speed settings,
material condition and lubrication.
CAUTION: Tap breakage may occur if tap is driven
too far without clearing chips. Choose tapping speed
and time settings that do not overload the tap by
driving it too far before reversing.
CAUTION: Use caution not to drive a tap past the end
of its threads, or to bottom a tap in a blind hole.
CAUTION: Always follow tap manufacturer's
guidelines for proper tap selection and use with
different materials, cutting fluids, tap drill sizes and
feed rates.
CAUTION: Precision Tap™ mode is not recommended
for use with taps less than 5/16" (8 mm) or more than
3/4" (20 mm) in diameter.
CAUTION: Recommended tapping speeds in Tables
2 and 3 are a suggestion only, based on test results
tapping new threads at 75% thread depth. It is
recommended to perform a test application on scrap
material, starting at speed 1 and working up. Tapping
mode should be used in the lowest speed that results
in an appropriate feed rate and chip clearing for
the material.
CAUTION: When using advanced tapping mode,
always start with the default forward time and reverse
time shown in Table 4, then increase or decrease
as necessary.
When the Precision Tap™ is enabled, the tool will operate in
forward and then automatically operate in reverse without
releasing the trigger. The tool will continue to alternate
between forward and reverse until the trigger is released.
D
WALT Tool Connect™
e
WARNING: To reduce the risk of injury, remove
accessories from the tool anvil before any Tool
Connect™ interaction.
NOTICE: Always check the tool configuration prior
to use. If you are unsure of the current configuration,
press the mode selector button
tool to the Home setting as described on the label and
this manual.
The DCF896 and DCF896H are capable of connecting
with mobile devices that support Bluetooth® Smart (or
Bluetooth® 4.0) technology. (To see if your mobile device
is compatible, visit: http://www.bluetooth.com/Pages/
Bluetooth‑Smart‑Devices‑List.aspx)
8
(Fig. D) to set the
D
WALT Tool Connect™ is an optional application for your
e
smart device (such as a smart phone or tablet) that connects
the device to your tool to allow you to configure specific
tool functions. Refer to Tool Connect™ Mode Selector.
NOTE: The Bluetooth® word mark and logos are registered
trademarks owned by the Bluetooth®, SIG, Inc. and any use
of such marks by D
WALT is under license. Other trademarks
e
and trade names are those of their respective owners.
nOTE: The Tool Connect™ App is governed by separate
terms and conditions available for viewing through the
mobile application.
Download the D
WALT Tool Connect™ application at:
e
•
Follow the instructions in the app to create your Tool
Connect™ account.
•
On the Home screen of the app, select "+ Tool" to begin
the process of adding your tool to the app.
•
To connect your tool with the D
app, at the appropriate screen, press the mode selector
button
8
for 3–5 seconds, then wait for the tool to
connect. The tool can only be connected to one Tool
Connect™ account at a time.
•
Once the tool has been connected, you can confirm that
you would like to register the product.
For more information on D
functionality and features, please call 1–800–4‑D
(1–800–433–9258), visit www.D
the FAQ page and help screens located inside the
mobile application.
Anvils (Fig. E, F)
WARNING: Use only impact-rated accessories. Non-
impact accessories may break and cause a hazardous
condition. Inspect accessories prior to use to ensure
that it con tains no cracks.
CAUTION: Inspect anvils, detent pins and hog rings
prior to use. Missing or damaged items should be
replaced before use.
Place the switch in the locked off (center) position or
remove battery pack before changing accessories.
Anvil with Detent Pin (Fig. E)
DCF896
To install an accessory on the anvil, align the hole in the
side of the accessory with the detent pin
Press the accessory on until the detent pin engages in the
hole. Depression of detent pin may be necessary to aid
installation of accessory.
To remove an accessory, depress the detent pin through
the hole and pull the accessory off.
English
WALT Tool Connect™
e
WALT Tool Connect™
e
WALT
e
WALT.com or view
e
9
on the anvil
3
.
9
Publicité
