Publicité
Les langues disponibles
Les langues disponibles
Horizontal
Orientation
ONE-KEY™
To learn more about the ONE-KEY™ functionality
for this tool, go to milwaukeetool.com/One-Key. To
download the ONE-KEY™ app, visit the App Store
or Google Play™ from your smart device.
ONE-KEY™ Indicator
Solid Blue
Wireless mode is active and
ready to be configured via the
ONE-KEY™ app.
Blinking Blue Tool is actively communicating with
the ONE-KEY™ app.
Blinking Red Tool is in security lockout and can
be unlocked by the owner via the
ONE-KEY™ app.
OPERATION
To reduce the risk of injury or tem-
WARNING
porary effects on vision, do not
look directly into the laser when it is on.
Use of controls or adjustments or
CAUTION
performance of procedures other
than those specified herein may result in hazard-
ous radiation exposure.
Perform the Accuracy Field Check
NOTICE
procedure immediately upon unboxing
of each new laser and before exposure to jobsite
conditions. See "Accuracy Field Check" for
information. Should any deviation from listed
product accuracy be found, please contact an
authorized MILWAUKEE service center. Failure to
do so could result in rejection of warranty claim.
Turning the Rotary Laser ON/OFF
• To turn the laser ON, press the power button. Once
the button is pressed, an audible tone will sound.
• When powered on, the laser will begin the leveling
sequence. Once level and ready for use, the Lev-
eling Mode Indicator LED will become solid green.
The laser will attempt to re-pair with its last paired
remote/receiver. If successful, an audible tone will
play, and the pairing LED will illuminate solid white.
If unsuccessful, the pairing LED will flash, and the
sound will play multiple times to indicate a failure
to pair.
• To turn the laser OFF, press the power button. The
laser diode will turn off, the head will stop rotating,
and all LEDs on the laser will turn off.
Vertical
Orientation
®
5
Pairing the Rotary Laser with the
Remote/Receiver
The laser must be paired with the remote/receiver to
use the laser to its full potential.
• To PAIR the tool with the remote/receiver, press
the pairing button for two seconds. While the tool
searches for the remote/receiver, the Pair Indicator
LED will flash white. When the device connection is
successful, an audible tone will sound, and the Pair
Indicator LED will remain solid white.
NOTE: The device you wish to pair with must also
be placed into a searching mode for it to become
discoverable.
• If the connection fails after 30 seconds, the Pair
Indicator LED will stop flashing, and the tool will beep
multiple times to indicate a failure. The operation will
need to be repeated.
Operating Modes
Rotational Mode
For best performance when using the remote/re-
ceiver, use 600 RPM. Different RPMs can be selected
by pressing the Rotational Speed Button on the laser
(1200, 300, and 600).
Sweep Mode
When using sweep mode, the laser beam oscillates
within a limited range. The visibility of the laser beam
is enhanced compared to rotational mode. Different
sweep angles can be selected by pressing the Sweep
button on the laser (0°,10°, 45°, and 90°).
Plumb Point Mode
The laser will default to Plumb Point Mode when
placed in the vertical orientation. Use the plumb
dot projected on the working surface to orient and
set up the lasers before entering the Rotational or
Sweep Mode.
Auto-Leveling Mode
When the laser initially turns on, the laser will au-
tomatically start to self-level. The Leveling Mode
Indicator LED will begin flashing green.
• During the leveling process, the Bump Alarm will
not be active. When the laser is leveled, the Level-
ing Mode Indicator LED will be solid green and
the laser head will start to rotate. The laser will be
ready for use.
• If the leveling process fails either by the one-minute
timer or out of leveling range, the Leveling Mode
Indicator LED flashes red, the laser diode turns off
and stops rotating, and an audible tone will sound.
NOTE: If the laser fails to level, ensure the laser
is on a stable surface. This error occurs when the
working surface causes the laser to be outside the
leveling range. After, try pressing the Leveling Mode
Button or power cycling the laser to trigger a relevel.
If the problem persists, please contact an authorized
MILWAUKEE service facility for support.
Complete Manual Mode
The laser will default to Auto-Leveling Mode. Com-
plete Manual Mode can be used to deactivate Auto-
Leveling and allow the user to manually position
the laser plane. Ensure the laser has self-leveled
(Leveling Mode Indicator LED is solid green).
1. Press the Leveling Mode button.
2. The Leveling Mode Indicator LED will turn solid red
and remains on (the laser will no longer attempt
to Auto-Level).
Publicité
