Cooper Lighting Solutions HALO MSS153T18B Manuel D'instructions

MSS153T18B
MSS153T18W
MST203T18B
MST203T18DB
MST203T18DW
MST203T18W
MST203T27B
MST203T27W
MSH303T27DW
MSH303T18B
MSH303T18W
ENGLISH
ITEMS REQUIRED
(Purchase separately)
• Phillips screwdriver
• Outdoor weatherproof silicone caulking
IMPORTANT SAFETY INSTRUCTIONS
When using product, basic precautions should always be followed, including the following:
• Heed all warnings, including below warnings AND those included on product.
• Save these instructions and warnings.
• For outdoor use only.
• cULus LISTED for wet location.
• Disassembling your fixture will void the warranty.
• Your fixture is prewired and preassembled for easy installation.
WARNING
• Read and follow these instructions.
• Risk of fire/electric shock. If not qualified, consult an electrician.
• Disconnect power at fuse or circuit breaker before installing or servicing.
CAUTION
• Connect fixture to a 120 volt, 60 Hz power source. Any other connection voids
the warranty.
• Fixture should be installed by persons with experience in household wiring or by a
qualified electrician. The electrical system, and the method of electrically connecting
the fixture to it, must be in accordance with the National Electrical Code and local
building codes.
• Mount fixture to a grounded, recessed-mounted standard junction box marked for use
in wet locations.
• Suitable for wall mount or eave mount only. NOT suitable for ground mount installation.
• For proper operation and protection against damage, the motion sensor head
adjustment knobs must be facing the ground.
• Do not mount below 5 feet.
NOTE: This equipment has been tested and found to comply with the limits for
a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio
frequency energy and if not installed and used in accordance with the instructions,
may cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television reception, which
can be determined by turning the equipment off and on, the user is encouraged to
Questions?/ Des questions?/ ¿Preguntas? 1-800-334-6871 ConsumerProducts@ cooperlighting.com
PACKAGING CONTENTS/ CONTENU DE L'EMBALLAGE/ CONTENIDO DEL PAQUETE
A. Motion detector B. Mounting bracket
and light fixture
Support de montage
Détecteur de mouvements
Soporte de montaje
et appareil d'éclairage
Detector de movimiento
y artefacto de luz
F. (2) #8-32 x 1-1/4 in. cover
E. FLD-KIT-SFCGNDW
mounting screws
Adapter Plate Kit
(2) vis de protection nº 8
Plaque adaptatrice trousse
de 32 x 1-1/4 po
Placa daptadora equipo
(2) Tornillos #8-32 x 1-1/4
pulg. de montaje de la cubierta
Instruction Manual/Manuel d'instructions/ Instrucciones
C. Gasket D. (2) #6-32 x 3/4 in. and (2) #8-32 x 3/4 in. junction box screws
(use the size that fits your junction box)
Joint
(2) vis nº 6 de 32 x 3/4 po et 2 vis nº 8 de 32 x 3/4 po pou
Junta
boîtier de jonction (choisissez la dimension convenant
à votre boîtier de jonction)
(2) Tornillos #6-32 x 3/4 pulg. y (2) tornillos #8-32 x 3/4 pulg.
para montaje de la caja de conexiónes (utilice el tamaño que
mejor se adecue a su caja de conexiónes)
G. (2) Decorative screw
cover caps
(2) cache-vis décoratifs
(2) Cubiertas tapatornillos
decorativas
try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
WARNING: FCC Regulations state that
any unauthorized changes or modifications
to this equipment not expressly approved by
the manufacturer could void the user's
authorization to operate this equipment.
SAVE THESE INSTRUCTIONS.
FOR BEST RESULTS
• Install the motion sensor 8-12 feet
above the ground. (Motion sensor is less sensitive
above 12 feet.)
• Locate motion sensor so motion moves across
detection zone (Fig. 1).
• Locate sensor away from heat producing sources to
prevent false triggering. Also be very careful not to
include objects such as windows, white walls and
water in the detection zone.
• Locate sensor away from moving objects such as
trees, large shrubs and street traffic.
• Do not install more than one motion activated
floodlight on one wall switch.
ADJUSTING THE COLOR TEMPERATURE (CCT)
• This product features selectable white color
tuning. Choose between three preset light colors
on the center dial of the base housing before,
during or after installation (fig. 2):
• These settings are designated by the abbreviations
located on the center dial on the base housing
(fig. 2):
3K = 3000K CCT, or soft white
4K = 4000K CCT, or neutral white [factory default]
5K = 5000K CCT, or daylight
• Use a flathead or Phillips head screwdriver to rotate
the dial so the arrow points toward the desired setting.
• DO NOT USE a power tool or over-rotate the dial.
1
H. Support hook
Gancho de soporte
Crochet
1
2
3
Wall mount
Eave mount
4
1-1/2 in. 1-1/2 in.
Round Octagonal