Publicité
Les langues disponibles
Les langues disponibles
Liens rapides
SERIES 51®
Hitch Shown In Proper Position
Equipment Required:
Fastener Kit: 51072F
Wrenches: 3/4 , 7/8, 21 mm
Drill Bits: None
Frame
1
Qty. (4)
Carriage Bolt 1/2-13 X 1-3/4
2
Qty. (4)
Spacer
Fasteners Typical Both Sides of Vehicle
Note: Factory Installed Steel Step Bumper and Brackets Must Be Used In Conjunction with Hitch
1. Remove existing M14 bolts from end of each frame rail.
2. Lift receiver into position, locating rearmost slots in receiver under existing weldnuts in vehicle frame.
3. Reinstall existing M14 bolts through receiver and frame into existing weldnuts.
4. Install remaining fasteners as shown.
Note: check hitch frequently, making sure all fasteners and ball are properly tightened. If hitch is removed, plug all holes in trunk pan or other body panels to
prevent entry of water and exhaust fumes. A hitch or ball which has been damaged should be removed and replaced. Observe safety precautions when working
beneath a vehicle and wear eye protection. Do not cut access or attachment holes with a torch.
This product complies with safety specifications and requirements for connecting devices and towing systems of the state of New York, V.E.S.C. Regulation V-5
and SAE J684.
z
2006 Cequent Towing Products
Installation Instructions
Chevrolet Silverado Pickup
GMC Sierra Pickup
(Requires OEM Bumper)
Note: Factory Installed Steel Step Bumper
and Brackets Must Be Used In
Conjunction with Hitch
Tighten M14 CL10.9 fasteners with torque wrench to 115 Lb.-Ft. (156 N*M)
Tighten all 1/2 GR5 fasteners with torque wrench to 75 Lb.-Ft. (102 N*M)
Do Not Exceed Lower of Towing Vehicle
Manufacturer's Rating or
Hitch type
Weight Distributing
Weight Carrying
1
Ball Mount
2
Wiring Access Location: PU3
Factory installed Bumper Bracket
- Typical Both Sides
Existing Weldnut Typical both sides
3
4
Existing M14 bolt
Note: All Fasteners Typical Both Sides of Vehicle
3
Qty. (4)
Conical Washer 1/2
4
Qty. (4)
Hex Nut 1/2-13
Sheet 1 of 3
51072N
Part Numbers:
51072
Max Gross
Max Tongue
Trailer WT (LB)
WT (LB)
7500 (3405 Kg)
750 (341 Kg)
5000 (2270 Kg)
500 (227 Kg)
11-15-06
Rev. A
Form: F205 Rev A 5-6-05
Publicité
Manuels Connexes pour Cequent Towing Products 51072
Sommaire des Matières pour Cequent Towing Products 51072
- Page 1 This product complies with safety specifications and requirements for connecting devices and towing systems of the state of New York, V.E.S.C. Regulation V-5 and SAE J684. Sheet 1 of 3 51072N 11-15-06 Rev. A 2006 Cequent Towing Products Form: F205 Rev A 5-6-05...
- Page 2 Ce produit est conforme aux normes V-5 et SAE J684 de la V.E.S.C. (État de New York) concernant les spécifications en matière de sécurité des systèmes d’attelage. Feuille 2 de 3 51072N 11-15-06 Rev. A 2006 Cequent Towing Products Form: F205 Rev A 5-6-05...
- Page 3 Este producto cumple con las especificaciones y requisitos de seguridad para conectar dispositivos y sistemas de remolque del estado de Nueva York. V.E.S.C. Regulación V-5 y SAE J684. Hoja 3 de 3 51072N 11-15-06 Rev. A 2006 Cequent Towing Products Form: F205 Rev A 5-6-05...