Publicité
Les langues disponibles
Les langues disponibles
Liens rapides
Frame
Hitch Shown In Proper Position
Equipment Required:
Fastener Kit: 24759N
Wrenches: 3/4", 15mm, 17mm
Drill Bits: 1/2"
Screwdriver
Taillight
access
2
1
Typical both sides
1
Qty. (2)
1/2"-13 X 1-3/4" Carriage bolt
2
Qty. (2)
1/4" X 1-1/2" X 2" Block
3
Qty. (2)
1/2" Lock washer
1.
Remove tow hooks if present. Return tow hooks & fasteners to owner.
2.
Remove both taillights by removing screw at bottom of light cover.
3.
Lower exhaust at (2) hangers, (1) at front and (1) at rear of muffler.
4.
Position hitch as shown and install M10 fasteners provided.
5.
Using hitch as a template, drill 1/2" holes in (2) places.
6.
Fishwire carriage bolt and block through access holes in taillight openings, as shown.
7.
Torque all fasteners to specifications shown below.
8.
Re-install exhaust hangers and taillights.
Note: check hitch frequently, making sure all fasteners and ball are properly tightened. If hitch is removed, plug all holes in trunk pan or other body panels to
prevent entry of water and exhaust fumes. A hitch or ball which has been damaged should be removed and replaced. Observe safety precautions when working
beneath a vehicle and wear eye protection. Do not cut access or attachment holes with a torch.
This product complies with safety specifications and requirements for connecting devices and towing systems of the state of New York, V.E.S.C. Regulation V-5
and SAE J684.
z
2005 Cequent Towing Products
Installation Instructions
Chrysler PT Cruiser
Bumper
Drawbar Kit:
3593
Drawbar must be used in the
RISE position only.
Tighten all 1/2" fasteners with torque wrench to 75 Lb.-Ft.
Tighten all M10 CL8.8 fasteners with torque wrench to 38 Lb.-Ft.
Do Not Exceed Lower of Towing Vehicle
2000 LB Max Gross Trailer Weight
200 LB Max Tongue Weight
Wiring Access Location: SUV 1, SUV 2
Frame rails
Existing weld nuts,
Typical both sides
Drilled holes
both sides
4
3
Typical both sides
4
Qty. (2)
1/2" Hex nut
5
Qty. (4)
M10 X 1.50 X 35mm CL8.8 Hex bolt
6
Qty. (4)
3/8" Conical washer
Sheet 1 of 3
Part Numbers:
Manufacturer's Rating or
Position blocks
as shown
5
6
Typical both sides
24759N
10-04-05
24759
77135
60818
Rev. A
Publicité
Manuels Connexes pour Cequent Towing Products 24759
Sommaire des Matières pour Cequent Towing Products 24759
- Page 1 Do not cut access or attachment holes with a torch. This product complies with safety specifications and requirements for connecting devices and towing systems of the state of New York, V.E.S.C. Regulation V-5 and SAE J684. Sheet 1 of 3 24759N 10-04-05 Rev. A 2005 Cequent Towing Products...
- Page 2 Ce produit est conforme aux normes V-5 et SAE J684 de la V.E.S.C. (État de New York) concernant les spécifications en matière de sécurité des systèmes d’attelage. Feuille 2 de 3 24759N 10-04-05 Rev. A 2005 Cequent Towing Products...
- Page 3 Este producto cumple con las especificaciones y requisitos de seguridad para conectar dispositivos y sistemas de remolque del estado de Nueva York. V.E.S.C. Regulación V-5 y SAE J684 Sheet 3 of 3 24759N 10-04-05 Rev. A 2005 Cequent Towing Products...