Publicité
Les langues disponibles
Les langues disponibles
Liens rapides
Frame
Hitch Shown In Proper Position
Equipment Required:
Fastener Kit: 75420F
Wrenches: 3/4", 7/8"
Drill Bits: None
NOTE! Use blocks
(Item 10) on long box
2500 & 3500 only.
10
Vehicle bumper bracket.
FIGURE 2
Qty.
1
1/2"-13 X 2 1/4" GR. 5 Hex Bolt
(2)
Qty.
2
1/2" Flat Washer
(2)
Qty.
3
1/4" X 1-1/2" X 2" Block
(2)
Qty.
4
1/2" Lockwasher
(6)
Qty.
5
1/2" Hex Nut
(6)
Note: check hitch frequently, making sure all fasteners and ball are properly tightened. If hitch is removed, plug all holes in trunk pan or other body
panels to prevent entry of water and exhaust fumes. A hitch or ball which has been damaged should be removed and replaced. Observe safety
precautions when working beneath a vehicle and wear eye protection. Do not cut access or attachment holes with a torch.
This product complies with safety specifications and requirements for connecting devices and towing systems of the state of New York, V.E.S.C.
Regulation V-5 and SAE J684.
2005, 2006 Cequent Towing Products
z
Installation Instructions
Dodge Ram Trucks-all without O.E.M. hitch
Bumper
NOTE! Orient blocks (Item 10) as
shown
Fishwire carriage
bolts thru slots in
frame; both sides.
See figure 3.
Hitch side
bracket.
Tighten all 1/2" GR5 fasteners with torque wrench to 75 Lb.-Ft. (102 N*M)
Do Not Exceed Lower of Towing Vehicle
Hitch type
Weight Distributing
Weight Carrying
Ball Mount
Wiring Access Location: PU 3
10
Use these holes for
long-bed.
Use these holes for
short-bed.
Between bumper bracket and
hitch side-brkt. As required.
See figure 2
Push/slide
¼" thick
blocks thru
end of frame,
both sides.
See figure 4
Qty.
6
(2)
Qty.
7
(4)
Qty.
8
(2)
Qty.
9
(2)
Qty.
10
(2)
Sheet 1 of 6
Manufacturer's Rating or
Max Gross
Trailer WT (LB)
10,000 (4540 Kg)
6,000 (2724 Kg)
Use this slot for
1500 models.
Typical both
sides.
FIGURE 1
3/8" X 1-1/2" X 3" Block, (use as needed)
1/2"-13 X 1-3/4" GR. 5 Carriage Bolt
1/4" X 1-1/2" X 3" Block
1/4" X 2" X 2" Block-square hole
3/16" X 2-1/8" X 2-1/8" Block-round hole,
(2500 & 3500 long box only)
75420N
6-23-06
Part Numbers:
75420
44536
82534
Max Tongue
WT (LB)
1,000 (454 Kg)
600 (272 Kg)
Use this slot for
2500/3500 models.
Typical both sides.
Rev. D
Publicité
Manuels Connexes pour Cequent Towing Products 75420
Sommaire des Matières pour Cequent Towing Products 75420
- Page 1 Do not cut access or attachment holes with a torch. This product complies with safety specifications and requirements for connecting devices and towing systems of the state of New York, V.E.S.C. Regulation V-5 and SAE J684. 2005, 2006 Cequent Towing Products Sheet 1 of 6 75420N 6-23-06 Rev.
- Page 2 Do not cut access or attachment holes with a torch. This product complies with safety specifications and requirements for connecting devices and towing systems of the state of New York, V.E.S.C. Regulation V-5 and SAE J684. 2005, 2006 Cequent Towing Products Sheet 2 of 6 75420N 6-23-06 Rev.
- Page 3 Ce produit est conforme aux normes V-5 et SAE J684 de la V.E.S.C. (État de New York) concernant les spécifications en matière de sécurité des systèmes d’attelage. 2005, 2006 Cequent Towing Products Feuille 3 de 6 75420N 6-23-06 Rev.
- Page 4 Ce produit est conforme aux normes V-5 et SAE J684 de la V.E.S.C. (État de New York) concernant les spécifications en matière de sécurité des systèmes d’attelage. 2005, 2006 Cequent Towing Products Feuille 4 de 6 75420N 6-23-06 Rev.
- Page 5 Este producto cumple con las especificaciones y requisitos de seguridad para conectar dispositivos y sistemas de remolque del estado de Nueva York. V.E.S.C. Regulación V-5 y SAE J684 2005, 2006 Cequent Towing Products Hoja 5 de 6 75420N 6-23-06 Rev.
- Page 6 No corte el acceso o los orificios del accesorio con soplete. Este producto cumple con las especificaciones y requisitos de seguridad para conectar dispositivos y sistemas de remolque del estado de Nueva York. V.E.S.C. Regulación V-5 y SAE J684 2005, 2006 Cequent Towing Products Hoja 6 de 6 75420N 6-23-06 Rev.