Ryobi RLM4018 Mode D'emploi page 5

■ Never pick up or carry the product while it
is running.
■ Turn off the product and disconnect it from
the power supply. Make sure that all moving
parts have come to a complete stop:
● whenever leaving the product unattended
(including disposal of grass clippings)
● before clearing blockages or unclogging
discharge chute
● before checking, cleaning, or working on
the product
● before removing the grass collector or
opening the grass discharge chute cover.
● after striking a foreign object; inspect the
product for damage and make repairs
as necessary before restarting and
operating the product.
● If the product starts to vibrate abnormally,
check immediately to:
– inspect for damage, particularly the
blades
– replace or repair any damaged parts
– check for and tighten any loose parts
■ The cutting blade
approximately parallel to the ground over
which it is being wheeled.
■ The blade on the product is sharp. Use
extreme caution, and wear heavy-duty
gloves when fitting, replacing, cleaning, or
checking bolt security.
■ Never operate the product if the on/off
switch on the handlebar does not properly
start and stop the product.
■ Never attempt to lock the on/off switches in
the on position, this is extremely dangerous.
■ Do not force the product. It will do the job
better and safer at the speed for which it
was designed.
■ Stop the blade when crossing gravel
surfaces.
■ Avoid holes, ruts, bumps, rocks, property
stakes, or other hidden objects. Uneven
terrain could cause a slip-and-fall accident.
■ Always ensure that the motor control cable
is never trapped, pinched, or otherwise
damaged during assembly or when folding
the handle. Never apply power to the product
if this cable is damaged. Have the product
serviced by an authorised service centre only.
■ Injuries may be caused, or aggravated, by
prolonged use of the product. When using
OVERLOAD PROTECTION DEVICE
The product has an overload protection device.
When overloading is detected, the product
automatically turns off . If the overload protector
is actuated, the motor must be allowed to cool
down for 5 to 10 minutes.
Turn off the product and disconnect it from
the power supply. The blades are sharp; wear
heavy-duty gloves before touching. Make
sure that the blade can rotate freely and is not
jammed or tight.
When the motor has cooled down, connect
the plug to the power supply, and turn on the
product. Press the start button, and squeeze
the on/off lever to start the product. If the
product still does not start, have the product
serviced by an authorised service centre only.
GENERAL MOWING TIPS
Adjust the cutting height of the lawnmower to
suit the current condition of the lawn.
should rotate
■
■
TRANSPORTATION AND STORAGE
■
■
■
■
the product for prolonged periods, ensure to
take regular breaks.
For best performance, always cut off one-
third or less of the total height of the grass.
When cutting long grass, reduce walking
speed to allow for more effective cutting and
a proper discharge of the clippings.
Turn off the product and disconnect it from
the power supply. Make sure that all moving
parts have come to a complete stop. Allow
the product to cool down before storing or
transporting.
Remove all foreign materials from the
product. Store the product in a cool, dry, and
well-ventilated place that is inaccessible
to children. Keep the product away from
corrosive agents such as garden chemicals
and de-icing salts. Do not store the product
outdoors.
For transportation, secure the product
against movement or falling to prevent
injury to persons or damage to the product.
Use extreme caution when lifting or tilting
the product for maintenance, cleaning,
storage, or transportation. The blade is
sharp; keep all body parts away from the
blade while it is exposed.
Original Instructions
EN
FR
DE
ES
IT
NL
PT
DA
SV
FI
NO
RU
PL
CS
HU
RO
LV
LT
ET
HR
SL
SK
BG
UK
TR
5