LG DLE5070 Serie Manuel D'utilisation page 32

32
troUBlEshootInG
Before calling for service (cont.)
Problem
Drying time is not • Heat settings, load size, or dampness of
consistent clothing is not consistent.
Clothes take too • Load is not properly sorted.
long to dry
• Large load of heavy fabrics.
• Dryer controls are not set properly.
• Lint filter needs to be cleaned.
• Exhaust ducts blocked, dirty, or duct run is
too long.v
• House fuse is blown, circuit breaker has
tripped, or power outage has occurred.
• Dryer is overloaded.
• Dryer is underloaded.
Clothes are wrinkled • Clothes dried too long (overdried).
• Clothes left in dryer too long after cycle
ends.
Clothes are shrinking • Garment care instructions are not being
followed.
TM
FLOW SENSE • Ductwork is too long or has too many turns/
indicator shows four restrictions.
bars during the drying
• Significant blockage of the ductwork due to
cycle
lint buildup or debris.
• The appliance has detected a restriction in
the external dryer venting.
SPECIFICATIONS
Dryer™ Models
Description
Electrical requirements*
Gas requirements*
Dimensions
Net weight
Drying capacity
- Normal cycle
Possible Causes
DLE5070* DLG5071*
Dryer
Please refer to the rating label regarding detailed information.
NG 4-10.5 inches WC
LP: 8–13 inches WC (Gas Models only)
27" (W) X 28 / " (D) X 45
15
16
68.6 cm (W) X 73.4 cm (D) X 115.3 cm (H), 127.5 cm (D with door open)
133.2 lbs (60.4 kg)
IEC 7.3 cu.ft. (22.5 lb/10.2 kg)
• The drying time for a load will vary depending on the heat setting, the type
of heat used (electric, natural gas, or LP gas), the size of the load, the type of
fabrics, the wetness of the clothes, and the condition of the exhaust ducts and
lint filter.
• Separate heavy items from lightweight items. Larger and heavier items take
longer to dry.
• Heavy fabrics take longer to dry because they tend to retain more moisture.
To help reduce and maintain more consistent drying times for large and heavy
fabrics, separate these items into smaller loads of a consistent size.
• Use the appropriate control settings for the type of load you are drying.
• Make sure the lint filter is cleaned before every load. With some loads that
produce high amounts of lint, it may be necessary to clean the filter during the
cycle.
• Confirm that the exhaust ductwork is properly configured and free of debris,
lint, and obstructions. Make sure that outside wall dampers can open properly
and are not blocked, jammed, or damaged.
• Reset circuit breaker or replace fuse. Do not increase fuse capacity. If the
problem is a circuit overload, have it corrected by a qualified electrician.
• Divide larger loads into smaller loads for drying.
• If you are drying a very small load, add a few extra items to ensure proper
tumbling action.
• Overdrying a load of laundry can lead to wrinkled clothes. Try a shorter drying
time, and remove items while they still retain a slight amount of moisture.
• Remove items from the dryer immediately at the end of the cycle. Use the
WRINKLE CARE option to continue tumbling clothes at the end of the cycle, for
up to 3 hours.
• To avoid shrinkage, please carefully follow the fabric care instructions for
your garment, because some fabrics will naturally shrink when washed. Other
fabrics can be washed but will shrink when dried in a dryer. Use a low or no
heat setting.
• Install a shorter or straighter duct run. See the Installation Instructions.
• Ductwork should be checked/cleaned soon.
Dryer can be used in this condition, but drying times may be longer.
• If exhaust restrictions are sensed by the FLOW SENSE
will remain on for two hours after the end of the cycle. Opening the door or
pressing the POWER button will turn off the display.
/ " (H), 50 / " (D with door open)
7 1
16 4
Solutions
TM
system, the indicator