Humanscale M/FLEX Instructions De Montage
Masquer les pouces
Voir aussi pour M/FLEX:
- Instructions d'assemblage (28 pages) ,
- Instructions de montage (16 pages)
Publicité
Liens rapides
Publicité
Manuels Connexes pour Humanscale M/FLEX
Sommaire des Matières pour Humanscale M/FLEX
- Page 1 Desk Mount Assembly Instructions FR 10 North America: +1 800 400 0625...
- Page 2 INSTALLATION HARDWARE ① ② ③ NOTE: 3 mm, 4 mm and 5 mm Hex Key can Cable Routing 3 mm 4 mm 5 mm Hook Hex Key Hex Key Hex Key be found under the plastic base cover. ④ ⑤ ⑥...
- Page 3 Assembly Instructions ① Attach Mount To Work Surface CAUTION: The following Desk Mounts cannot be used to mount M/Flex to any wall or vertical surface. Clamp Mount A - For installation on an open edge of a work surface: Slide the Clamp Mount (A) all the way against the edge of the work surface.
- Page 4 Sliding Desk Mount ① D - For installation with minimal clamp space: Skip to step 3, if the Clamp Mount is not attached. Remove Base Cover (H) by lifting it up and off. Loosely attach Sliding Clamp (L) to the Base Plate (M) with the Base Screws (J).
- Page 5 Bracket Assembly And Cable Clip Single And Dual Monitor Applications With the Lever (A) open, position the Dual Bracket (B) at the desired height on the Post (C). Close the Lever entirely. If you are adding a second monitor, lift and remove the Cover (D). ①...
- Page 6 Smart Stop Adjustment A Smart Stop Ring is included at every Quick Attach joint. Position the Smart Stop Ring to limit the arm’s range of motion. The marked angle will be in the center of the range of motion. NOTE: The stop rings must be configured in such a way that does not allow the monitor to pass behind the rear edge of the unit. ①...
- Page 7 Attach Vesa Plate To Monitor Separate the VESA cover from the VESA plate. Position the VESA plate over the mounting holes on the back of monitor with the D-shaped cutouts (A) in a vertical orientation. Attach using provided VESA screws. Snap the VESA cover back in place.
- Page 8 Push Cap on top of second Post. M/Flex Clamp Adjustments ⑥ Your M/Flex arrives ready for use, however it may become necessary to adjust the clamp. Remove monitors and links from the Bracket. Open the Lever (A) all the way.
- Page 9 Weight Adjustments Your monitor should move up and down easily and stay in position. If the monitor moves down from the desired position, or is hard to ① lift, you should increase the counterbalance force. If the monitor moves up from the desired position you should decrease the counterbalance force.
- Page 10 Passez à l’étape 3 si le support de fixation n’est pas fixé. ATTENTION : Les supports de bureau suivants ne peuvent pas être utilisés pour monter le bras M/Flex sur un mur ou une Reportez-vous aux étapes 1D - 1, 2 pour retirer le support surface verticale.
- Page 11 Fixer La Plaque Vesa À L’écran Si vous ajoutez un deuxième écran, soulevez et retirez le couvercle (D). Enlevez le couvercle VESA de la plaque VESA. Voir Page 5, ① , ② & ③ Placez la plaque VESA sur les trous de montage à l’arrière de l’écran en orientant les découpes en forme de D (A) à...
- Page 12 ATTENTION : Ne serrez pas excessivement la vis de réglage car cela pourrait endommager le bras. Votre pince M/Flex est livrée prête à l’emploi, mais il peut s’avérer nécessaire de l’ajuster. Les écrans ne doivent pas avoir un poids supérieur à : 15,5 lb (7 kg) pour M2.1...
- Page 14 For our terms and conditions please go to https://www.humanscale.com/about/legal-information/terms-conditions.cfm © 2023 Humanscale Corporation. The text and artwork are copyrighted materials. All rights reserved. The Humanscale mark and logo are trademarks of Humanscale Corporation and are registered in the United States and certain other countries.