Publicité
Page 3 of 12
•
To fit the R&G Exhaust Hanger, the OEM pillion footrest mounting bracket needs to be removed.
•
To do this, remove the two mounting bolts at the top of the pillion footrest mounting bracket,
and the one OEM bolt holding the footrest to the exhaust silencer, then remove the OEM pillion
footrest mount from the motorcycle.
•
Take the R&G Exhaust Hanger (Item 1) and fit the two M8 x 20mm long countersunk head
bolts (Item 5) through the two top mounts of the exhaust hanger as shown in the assembly
picture.
•
Offer the exhaust bracket into position and engage both bolts into the pillion foot peg mounting
holes (do not fully tighten at this stage).
•
With the exhaust hanger loosely mounted on the motorcycle, ensure the lower part of the
exhaust hanger is on the outside of the exhaust mounting bracket.
•
Place the M8 button head bolt (Item 2) through the washer (Item 3) & exhaust hanger
mounting bracket before fitting the M8 nut (Item 4) onto the exposed thread of the bolt and
loosely tighten as shown in the assembly picture.
•
Ensure the exhaust hanger is correctly fitted before tightening all three bolts.
•
Please ensure when the motorcycle is being used that no parts are in such a position that they
may collide/damage other bike parts (this is particularly important if using after-market cans or
exhaust systems).
Please note that it is your responsibility to ensure that no part of the exhaust hanger or
exhaust assembly fouls or comes into contact with other parts of the machine. Do not ride
the motorcycle until this aspect has been verified and you have compressed the rear
suspension (if appropriate to the design of the motorcycle) to test this thoroughly.
The catalogue description and any exhibition of samples are only broad indications of the Products and R&G may make design
changes which do not diminish their performance or visual appeal and supplying them in such state shall conform to the order.
The Buyer acknowledges no representation or warranty (other than as to title) has been given or will apply to the Products other
than those in R&G's order or confirmation and the Buyer confirms it has chosen the Products as being of merchantable quality and
suitable for its particular purposes. Where R&G fits the Products or undertakes other services it shall exercise reasonable skill and
care and rectify any fault free of charge unless the workmanship has been disturbed. The Buyer is responsible for ensuring that
the warranty on the motorcycle is not affected by the fitting of the Products. On return of any defective Products R&G shall at its
option either supply a replacement or refund the purchase money but shall not be liable if the Products have been modified or
used or maintained otherwise than in accordance with R&G's or manufacturer's instructions and good engineering practice or if the
defect arises from accident or neglect. Other than identified above and subject to R&G not limiting its liability for causing death
and personal injury, it shall not be liable for indirect or consequential loss and otherwise its liability shall be limited to the amounts
paid by the Buyer for the Products or the fitting or service concerned. These terms do not affect the Buyer's statutory rights.
Returns must be pre-authorised (if not pre-authorised the return will be rejected). Goods may only be returned direct to us if they
were purchased direct from us (customer must prove if necessary). Otherwise to be returned to original vendor. Goods must be
in re-sellable condition, in the opinion of R&G. All returns are subject to a 25% restocking and handling fee (25% of the gross
value exc. P&P – at the prevailing price at time of purchase). The customer must pay any and all carriage charges. No returns of
discontinued products, unless within 14 days of purchase. This policy does not affect your statutory rights and does not refer to
faulty goods.
Unit 1, Shelley's Lane, East Worldham, Alton, Hampshire, GU34 3AQ
Tel: +44 (0)1420 89007 Fax: +44 (0)1420 87301
FITTING INSTRUCTIONS
Issue 1 - 01/03/2024 (MH)
CONSUMER NOTICE
R&G RETURNS POLICY (NON-FAULTY GOODS)
R&G Racing
www.rg-racing.com
EH0124
Email:
info@rg-racing.com
Publicité
