Télécharger Imprimer la page

CONTINENTAL EDISON CELED32S0817B3 Mode D'emploi page 47

Publicité

Les langues disponibles

Les langues disponibles

OK button. Then select Delete Timer on Event option.
The timer will be cancelled.
Notes: You cannot switch to any other channel or source while
there is an active recording or timer on the current channel.
It is not possible to set timer or record timer for two or more
individual events at the same time interval.
Teletext Services
Press the Text button to enter. Press again to activate mix
mode, which allows you to see the teletext page and the
TV broadcast at the same time. Press once more to exit. If
available, sections in the teletext pages will become colour-
coded and can be selected by pressing the coloured buttons.
Follow the instructions displayed on the screen.
Digital Teletext
Press the Text button to view digital teletext information.
Operate it with the coloured buttons, cursor buttons and the
OK button. The operation method may differ depending on
the contents of the digital teletext. Follow the instructions
displayed on the digital teletext screen. When the Text button
is pressed again, the TV returns to television broadcast.
Software Upgrade
Your TV is capable of finding and updating the firmware
automatically via the broadcast signal or via Internet.
Software upgrade search via user interface
On the main menu select System>Settings and then
More. Navigate to Software upgrade and press the
OK button. In Upgrade options menu select Scan
for upgrade and press OK button to check for a new
software upgrade.
If a new upgrade is found, it starts to download the
upgrade. After the download is completed confirm the
question asking about rebooting the TV by pressing the
OK to continue with the reboot operation.
3 AM search and upgrade mode
Your TV will search for new upgrades at 3:00 o'clock if
Automatic scanning option in the Upgrade options
menu is set to Enabled and if the TV is connected to
an aerial signal or to Internet. If a new software is found
and downloaded successfully, it will be installed at the
next power on.
Note: Do not unplug the power cord while led is blinking during
the reboot process. If the TV fails to come on after the upgrade,
unplug, wait for two minutes then plug it back in.
Troubleshooting & Tips
Tv will not turn on
Make sure the power cord is plugged in securely to wall
outlet. Check if batteries are exhausted. Press the Power
button on the TV.
Poor picture
• Check if you have selected the correct TV system.
• Low signal level can cause picture distortion. Please
check antenna access.
• Check if you have entered the correct channel
frequency if you have done manual tuning.
• The picture quality may degrade when two devices are
connected to the TV at the same time. In such a case,
disconnect one of the devices.
No picture
• This means your TV is not receiving any transmission.
Make sure the correct source has been selected.
• Is the antenna connected properly?
• Is the antenna cable damaged?
• Are suitable plugs used to connect the antenna?
• If you are in doubt, consult your dealer.
No sound
• Check if the TV is muted. Press the Mute button or
increase the volume to check.
• Sound may be coming from only one speaker. Check
the balance settings from Sound menu.
Remote control - no operation
• The batteries may be exhausted. Replace the batteries.
Input sources - can not be selected
• If you cannot select an input source, it is possible that
no device is connected. If not;
• Check the AV cables and connections if you are trying
to switch to the input source dedicated to the connected
device.
Recording unavailable
To record a programme, you should first connect a USB
disk to your TV while the TV is switched off. You should
then switch on the TV to enable recording feature. If
you cannot record, try switching off the TV and then re-
inserting the USB device.
USB is too slow
If a "USB disk writing speed too slow to record"
message is displayed on the screen while starting a
recording, try restarting the recording. If you still get the
same error, it is possible that your USB disk does not
meet the speed requirements. Try connecting another
USB disk.
English - 45 -

Publicité

loading