Location Requirements - Jenn-Air JMW2427DB Instructions D'installation

Parts Supplied
Deflector bracket
■
Plastic spacers - (4) single ovens, (6) double ovens,
■
(4) combo oven
#8-18 x 1/4" (6.3 mm) screws - (2) for 27" (68.6 cm) models;
■
(4) for 30" (76.2 cm) models - deflector bracket
(4) #8-18 x 3/8" (9.5 mm) screws - oven feet
■
(2) feet
■
(2) front feet
■

Location Requirements

IMPORTANT: Observe all governing codes and ordinances.
NOTE: Refer to the following "Location Requirements" and the
"Location Requirements" section of the Installation Instructions
provided with your built-in oven.
Cabinet opening dimensions that are shown must be used.
■
Given dimensions provide minimum clearance for the oven.
The recessed installation area must provide complete
■
enclosure around the recessed portion of the oven.
The oven support surface must be solid, level and flush with
■
the bottom of the cabinet cutout.
The floor must be able to support a total weight (microwave
■
and built-in oven) of 286 lbs (130 kg).
IMPORTANT: To avoid damage to your cabinets, check with
your builder or cabinet supplier to make sure that the materials
used will not discolor, delaminate or sustain other damage. This
oven has been designed in accordance with the requirements
of UL and CSA International and complies with the maximum
allowable wood cabinet temperatures of 194°F (90°C).
Deflector Bracket Dimensions
27" (68.6 cm) Models
A. 26 ⁄ " (68.4 cm) overall width
15
16
Cabinet Dimensions - Flush Installations
A 25" (63.5 cm) minimum cutout depth is required.
These dimensions will result in a 1/4" (6.3 mm) reveal on the top,
a 1/4" (6.3 mm) reveal on the sides, and a 1/8" (3.1 mm) reveal
on the bottom of the wall oven.
The front face of the cleats and platform will be visible and
should be treated as a finished surface.
06-May-2019 13:38:42 EDT | RELEASED
A
30" (76.2 cm) Models
A. 29 ⁄ " (76.0 cm) overall width
15
16
In some European factories the letter "W" of the part code mentioned herein will be automatically
A
B
C
D
E
F
G
H
Front View
27" (68.6 cm) Models
A. 5/8" (1.6 cm) top cleat*
B. 27 / " (69.2 cm) minimum width
1
4
of flush inset cutout
C. 25 / " (65.7 cm) minimum width
7
8
of opening
D. 44 / " (112.5 cm) minimum
5
16
height of flush inset cutout
E. 43 / " (110.9 cm)
11
16
recommended cutout height
F. 11/16" (1.7 cm) side cleat*
G. 1/2" x 2" (1.3 cm x 5.1 cm)
spacer the entire depth of the
cutout*
H. Recommended junction box
location
I. 4 / " - 19 / " (11.7 cm - 48.9 cm)
5 1
8 4
bottom of cutout to floor
J. 25" (63.5 cm) minimum depth of
cutout
*Cleats and spacers must be recessed 1
front of the cabinet.
A
C
D
Top View
27" (68.6 cm) Models
A. 1/2" x 2"
(1.3 cm x 5.1 cm)
spacer the entire depth
of the cutout*
B. 25" (63.5 cm) depth of
cutout
/
C. 1 3 " (3.5 cm) recess
8
from front of cabinet
D. 11/16" (1.7 cm) side
cleat*
*Cleats and spacers must be recessed 1
front of the cabinet.
replaced by the number "4000" (e.g. "W12345678" becomes "400012345678")
F
G
J
H
I
Side View
30" (76.2 cm) Models
A. 5/8" (1.6 cm) top cleat*
B. 30 / " (76.8 cm) minimum width
1
4
of flush inset cutout
C. 28 / " (73.3 cm) minimum width
7
8
of opening
D. 44 / " (112.5 cm) minimum
5
16
height of flush inset cutout
E. 43 / " (110.9 cm)
11
16
recommended cutout height
F. 11/16" (1.7 cm) side cleat*
G. 1/2" x 2" (1.3 cm x 5.1 cm)
spacer the entire depth of the
cutout*
H. Recommended junction box
location
I. 4 5 / " - 19 1 / " (11.7 cm - 48.9 cm)
8 4
bottom of cutout to floor
J. 25" (63.5 cm) minimum depth of
cutout
3 / " (3.5 cm) from the
8
A
B
D
30" (76.2 cm) Models
A. 1/2" x 2"
(1.3 cm x 5.1 cm)
spacer the entire depth
of the cutout*
B. 25" (63.5 cm) depth of
cutout
/
C. 1 3 " (3.5 cm) recess
8
from front of cabinet
D. 11/16" (1.7 cm) side
cleat*
⁄ " (3.5 cm) from the
3
8
3