Cycle Modifiers; Cycle Options - Whirlpool WED560LHW Guide D'utilisation Et D'entretien

Washing
During the wash cycle, this will display to let you know
the cycle is in progress.
Drying (on some models)
During a drying cycle, this will display to let you know
the drying cycle is in progress.
Cool Down (on some models)
At the end of a drying cycle, your load will go through
a cool-down period.
PreSoak
This symbol will be displayed to let you know
a presoak is in progress.
Detergent Low (on some models)
When detergent in the bulk dispenser is running low,
the display will show the detergent level (Low).
Add Garment
When "Add Garment" is displayed, you may pause the
washer, open the door, and add items. Touch and hold
START/PAUSE to start the washer again.
Door Locked
The Door Locked symbol will display to
indicate that the door is locked and cannot
be opened without first pausing or canceling the cycle.
Control Lock
When the Contol Lock symbol is displayed,
the buttons are disabled. Touch and hold EXTRA
RINSE for 3 seconds to enable the buttons.
FanFresh (on some models)
®
This symbol will be displayed when the FanFresh
option is activated. The fan will turn on and the
load will tumble periodically for up to 12 hours.
End
Once the cycle is complete, "End" will display. Remove
the load promptly for best results.

CYCLE MODIFIERS

5
When you select a cycle, its default settings will light up.
Touch to adjust cycle modifiers on the washer before
touching START/PAUSE. Additional wash modifiers or
options selected after touching Start/Pause may not activate.
Once a wash setting is selected, it is saved for the cycle
selected. To return to factory default cycle settings, unplug
washer for 30 seconds; then plug back in. See "Cycle Guide"
for default cycle settings.
NOTE: Some modifiers may increase or decrease the
estimated time remaining.
Temp
The recommended wash temperature is preset for
each cycle. Some preset temperatures can be changed.
You may select a different wash temperature based on
the level of soil and type of fabric being washed. For
best results, use the warmest wash water safe for your
fabric, following the garment label instructions. All wash
temperatures feature a cold rinse.
Spin
The recommended spin speed is preset for each cycle.
Some preset speeds can be changed.
■ Faster spin speeds mean shorter dry times, but may
increase wrinkling in your load.
■ Slower spin speeds reduce wrinkling, but will leave
your load more damp.
Soil
The recommended soil level is preset for each cycle.
Some preset soil levels can be changed. For heavily
soiled and sturdy fabrics, select the Heavy Soil Level
setting. For lightly soiled and delicate fabrics, select the
Light Soil Level setting. Lower soil level settings will help
reduce tangling and wrinkling.
6
6
UTILITY CYCLES
Clean Washer
Use this every 30 washes to keep the inside of your
washer fresh and clean. This cycle uses a higher water
level. Use with affresh
chlorine bleach to thoroughly clean the inside of your
washer. When using this cycle, the drum should be
empty. This cycle should not be interrupted. See the
"Washer Care" section.
Drain & Spin
This cycle removes excess water from the load or
special-care items washed by hand. Use this cycle
after a power failure. For some fabrics, you may choose
to set a slower spin speed. On some models: Touch
and hold DRAIN & SPIN for 3 seconds to set a Dry Only
cycle.

CYCLE OPTIONS

7
You may add or remove options for each cycle. Not all
options can be used with all cycles, and some are preset
to work with certain cycles. Options vary by model.
Steam Clean (on some models)
The Steam Clean option adds additional soak and
wash time to many cycles to help remove tough stains,
as well as a steam boost for added cleaning power.
An integrated heater helps to maintain optimal wash
temperatures. See "Cycle Guide" for cycles that allow
the Steam Clean option.
You can also touch and hold STEAM CLEAN
for 3 seconds to turn cycle signals on or off.
hold 3 sec for hold 3 sec for
Extra Rinse
®
Cycle Signal Control Lock
Activate this option to add an extra rinse to most
cycles.
You can also touch and hold EXTRA RINSE
for 3 seconds to disable/enable the Control Lock.
Wash & Dry (on some models)
Touch to add a drying cycle to your load after the wash
cycle has finished. The Wash & Dry option is designed
to wash and dry small loads overnight. Cycle time
will vary based on load composition. For optimal dry
performance and cycle time, load the drum no more
than one-quarter full. The cycle will automatically
terminate after a maximum 12-hour cycle time.
You can also touch and hold WASH & DRY for
3 seconds to activate/deactivate the FanFresh
option. Use the FanFresh
unable to remove the load promptly. The washer
will automatically activate the fan after the cycle ends
and tumble the load periodically for up to 12 hours.
IMPORTANT:
■
■
Load & Go™ (on some models)
Touch to select this option If you want to automatically
add HE detergent to the wash load at the proper time.
IMPORTANT: When using the dispenser cartridge
with concentrated liquid detergent, be sure to change
the detergent concentration settings in the control if
the detergent used is different than factory preset of
2x concentration. Change the detergent concentration
setting by touching and holding TEMP and SOIL for
3 seconds.
You can also touch and hold LOAD & GO™ for 3
seconds to set a presoak.
PreSoak (on some models)
Touch to add a presoak time of your choice
to a wash cycle.
Washer Cleaner tablets or liquid
®
hold 3 sec for
FanFresh
option if you will be
®
Do not use dryer sheets.
Do not dry comforters or large blankets.
hold 3 sec for
PreSoak
®