Publicité
Les langues disponibles
Les langues disponibles
ADD TITLE: CONTINUOUS PILOT / INTERMITTENT PILOT (CPI / IPI) SELECTION
A. When the transmitter is in the off position, use the mode key to guide
remote control layout
you to the CPI mode icon.
EN
B. Press the up/down to switch between IPI and CPI modes. A single
3.3
in the event of a battery failure
beep will confi rm reception of the command.
If the receiver batteries fail, the appliance will no longer turn on or off. To operate the appliance in the event of
note:
a battery failure, the slide switch located on the receiver may be switched to the "ON" position to operate the
If the appliance is equipped with a CPI/IPI toggle switch, set the CPI/IPI
appliance.
to CPI position to enable remote CPI operation. If the switch is set to IPI
then it will only work in IPI regardless of what is set on the remote control
handset.
3.4
low battery
ADD TITLE: LOW BATTERY / MANUAL BYPASS
The life span of the remote batteries depends on various factors: quality of the batteries,
the number of ignitions, etc.
When the transmitter batteries are low, a battery icon will appear on the LCD display
before all battery power is lost. When the batteries are replaced, this icon will disappear.
When the receiver batteries are low, no "beep" will be emitted from the receiver when
it receives an on/off command. This in an alert for the receiver that there's low battery.
When the batteries are replaced the "beep" will be emitted from the receiver when the on/off key is pressed.
If the batteries of the receiver or transmitter are low, the appliance can be turned on manually by sliding the
three position slider switch on the receiver to the on position. This will bypass the remote control feature and the
appliance main burner will come on if the gas valve is in the on position.
ADD TITLE: IN THE EVENT OF A POWER FAILURE
If the receiver is equipped with batteries they will enable fl ame height control or on/off function to control the
appliance during a power failure. Blower and Night Light™ operation is not possible. Refer to "appliance
operation" section when communications between receiver and transmitter have been lost. The receiver will
emit a "beep" sound to confi rm programming has been successful once power is restored. During a power
failure, if the appliance was on, the fl ame height will stay at the setting prior to the failure. If off when the failure
occurs and then turned on, the fl ame height will come on at "Hi". The fl ame height can then be controlled by the
remote.
12
W415-4151 / --1 / 12.18.23
68
Flame Off
MAX
Set Temperature
76
child lock
OFF
SMART
Flame Off
MAX
76
child lock
OFF
73
73
Flame Off
child lock
Room Temperature
Room Temperature
68
ON
68
ON
Set Temperature
Set Temperature
SMART
SMART
MAX
76
MAX
76
OFF
OFF
Flame Off
Flame Off
child lock
child lock
Flame at level 1
76
76
°F
°F
°F
76
Blue LCD Display
°F
On / Off Key
Blue LCD Display
Temperature Key
On / Off Key
Up / Down Arrow Key
Temperature Key
Flame at level 1
Up / Down Arrow Key
76
Mode Key
°F
76
Mode Key
°F
°F
23
°F
°C
23
°F
°C
Flame at level 1
76
°F
76
°F
76
°F
76
°F
76
°F
76
°F
°F
76
°F
°F
Flame at level 1
76
Flame at level 1
°F
76
°F
Flame at level 5
Flame at "Hi" level 6
76
76
76
76
°F
°F
76
76
76
OFF
IPI
CPI
°F
°F
OFF
Hi
76
°F
OFF
Flame at level 5
Flame at "Hi" level 6
76
76
°F
76
IPI
CPI
76
76
°F
76
Hi
Flame at level 5
Flame at "Hi" level 6
76
76
76
°F
°F
IPI
CPI
68
76
°F
68
76
°F
OFF
76
°F
OFF
76
°F
76
°F
Flame at level 5
Flame at "Hi" level 6
76
23.3
Flame at level 5
°F
Flame at "Hi" level 6
IPI
CPI
76
°F
IPI
CPI
°F
°F
76
°F
°F
ON
76
°F
ON
°F
°F
°F
°F
76
°F
°F
Hi
76
°F
Hi
76
°F
76
°F
76
°F
76
Hi
°F
Hi
76
°F
76
°F
Publicité
