Télécharger Imprimer la page

Ryobi RY36LMMX51A Traduction Des Instructions Originales page 5

Publicité

Les langues disponibles
  • FR

Les langues disponibles

  • FRANÇAIS, page 9
Never operate the product if the on/off
switch on the handlebar does not properly
start and stop the product.
Never attempt to lock the on/off switches in
the on position; this is extremely dangerous.
Do not force the product. It will do the job
better and safer at the speed for which it
was designed.
Stop the blade when crossing gravel
surfaces.
Do not pull the product backwards unless
absolutely necessary. If you must back the
product away from a wall or obstruction,
first look down and behind to avoid tripping
or pulling the product over your feet.
Turn off the motor and allow the blade
to stop if the product has to be tilted for
transportation when crossing surfaces
other than grass, and when transporting
the product to and from the work area.
Never use the product with defective guards
or shields, or without safety devices, such
as deflectors or grass collectors, in place.
Do not tilt the product when turning on
the motor or while the motor is running. If
absolutely necessary, you may raise the
front of the lawnmower by no more than 5
cm to enable easier starting. Press down
on the handlebar to achieve this. Always
return the lawnmower to its normal position
with all wheels on the ground before cutting.
Tilting the lawnmower exposes the blade and
increases the probability of objects being
thrown and accidental contact with the blade.
Turn on the motor carefully according to
instructions and keep hands and feet away
from blades. Do not put hands or feet near
or under rotating parts.
Never pick up or carry the product while it
is running.
Turn off the product, and remove the
isolator key and the battery pack. Make
sure that all moving parts have come to a
complete stop:
whenever leaving the product unattended
(including disposal of grass clippings)
before clearing blockages or unclogging
discharge chute
before checking, cleaning, or working on
the product
after striking a foreign object; inspect the
product for damage and make repairs
as necessary before restarting and
operating the product
If the product starts to vibrate abnormally
(check immediately)
inspect for damage, particularly the
blades
replace or repair any damaged parts
check for and tighten any loose parts
Avoid holes, ruts, bumps, rocks, property
stakes, or other hidden objects. Uneven
terrain could cause a slip-and-fall accident.
Always ensure that the motor control cable is
never trapped, pinched or otherwise damaged
during assembly or when folding the handle.
ADDITIONAL BATTERY SAFETY
WARNINGS
WARNING
To reduce the risk of fi re, personal injury,
and product damage due to a short circuit,
never immerse your tool, battery pack or
charger in fl uid or allow a fl uid to fl ow inside
them. Corrosive or conductive fl uids, such
as seawater, certain industrial chemicals,
and bleach or bleach-containing products,
etc., can cause a short circuit.
PRODUCT FEATURES
OVERLOAD AND OVERHEAT PROTECTION
The product has an overload protection device.
When overloading is detected, the product will
automatically turn off. If the overload protector
is actuated, the on/off lever must be released.
Squeeze the on/off lever to restart the product.
The battery pack has overheat protection.
Excessive temperatures will cause the battery
to stop powering the product. If the battery
pack is too warm, allow it to cool down before
resuming operation. If the product still does
not work, recharge the battery.
NOTE: The battery pack LED indicator will
not work if the battery protection feature has
caused the battery pack to stop powering the
product. Turn off the product or remove the
battery pack from the product and the battery
pack LED indicator will resume normal function.
TELESCOPIC HANDLE
The product is equipped with a telescopic
handle that can be adjusted for storage and
EN
FR
DE
ES
IT
NL
PT
DA
SV
FI
NO
RU
PL
CS
HU
RO
LV
LT
ET
HR
SL
SK
BG
UK
TR
English |
3

Publicité

loading