Publicité
Les langues disponibles
Les langues disponibles
START/STOP THE VACUUM CLEANER AND ADJUST SUCTION
PARKING POSITIONS
REPLACING THE DUSTBAG, S-BAG®
NB: Always change the s-bag when S-BAG indicator is illuminated or has red light even
if the s-bag is not full (it may be blocked) and after using carpet cleaning powder. For
best possible performance, use the Ultra Long Performance bag which is especially
developed for your cleaner. Other synthetic s-bags can also be used. Do not use paper
dust bags! www.s-bag.com
When you start the cleaner after s-bag replacement, It takes 10 seconds before the
S-BAG indicator turns off or turns green.
POWER
Pull out the power cord and plug
it into the mains. Press the ON/
OFF button to turn the cleaner on/
off. Indicators light up, LOW/HIGH
indicator lights up from left to
right and back. Press the ON/OFF
button on the remote control to
turn the cleaner on/off.
Adjust suction power: The cleaner
starts in AUTO mode (automatic
power regulation). AUTO indicator
is illuminated on the display and
LOW/HIGH indicator pulses. To
regulate power manually press
+/- button on handle. Press AUTO
button to return to auto-function.
After cleaning, push the REWIND
button to rewind the cable.
Use parking position on the side
(A) or underneath (C) to carry and
store the cleaner. At the back (B)
when you pause (save your back).
Replace the s-bag when S-BAG
indicator lights up in red
(green light: bag is OK, yellow light:
soon time to replace bag).
Open the dust compartment cover
by pulling the S-BAG button.
Pull the cardboard handle to close
and remove the s-bag®
Insert a new s-bag® by pushing
the cardboard straight down in its
tracks. Close the lid. If the s-bag® is
not properly placed or is missing,
the lid will not close.
REPLACING THE FILTERS
NB: Do not use cleaning agents. Avoid touching the filter surface. Let the filter dry
completely (min. 24 h in room temperature) before putting back ! Change the washable
filter at least once a year or when it is very dirty or damaged. Do not remove the
L-shaped foam under the filter.
NB: When you start the cleaner after filter replacement, It takes 10 seconds before the
FILTER indicator turns green or turns off.
VACUUMING WITH THE UNIVERSAL NOZZLE
CLEANING THE UNIVERSAL NOZZLE
CLEANING THE TURBO NOZZLE
3IN1 ACCESSORY TOOL
Replace/clean the filter when filter
indicator lights up in red. Green
light indicates that the filter is ok.
It lights up briefly when you start
the vacuum cleaner.
Pull the FILTER button to open
the filter lid. Use original s-filters.
Remove the filter and check the
reference on the frame to define
type. Replace with a new filter or
clean it. Rinse the inside (dirty
side) in lukewarm tap water. Tap
the filter frame to remove the
water. Repeat the process four
times.
After replacing the filter, close the
filter lid until it is clicked back into
place. If the filter lid comes off,
position the hinges at the bottom
and push the filter lid until it is
clicked back into place.
Replace the motor filter when dirty
or after every 5th s-bag. Push the
filter holder down and pull it out.
Exchange the filter and close the
lid.
For deep cleaning on carpet,
change the nozzle setting with
the slider to Carpet mode. Icon
illustrates recommended floor
type. Move the nozzle forward. The
front light turns on automatically
after a few seconds. When the
nozzle is not used, the light turns
off automatically after a few
seconds.
Disconnect the nozzle from the
tube. Clean with the hose handle.
Disconnect the nozzle from the
tube and remove entangled
threads etc by snipping them away
with scissors. Use the hose handle
to clean the nozzle.
Pull the textile tab to take out 3in1
tool. The tool has 3 functions, see
pictures on next page.
After usage, put it back in its place.
Publicité
