Publicité
Côté droit (lorsqu'on est assis sur la moto)
Enlever les boulons de fixation moteur montrés sur la photo 'B' (utiliser la clé de 13mm. Veillez
•
à ce que les entretoises du cadre au moteur ne tombent pas (elles devront être en position pour la
fixation des sliders de cadre).
Page | 6
•
Glisser 2 rondelles 10mm (article 4) sur les 2 boulons longs M10 (article 5) (90mm de long) de
façon à ce que la rondelle se place contre le boulon.
•
Glisser ensuite les boulons avec les rondelles dans un des sliders de cadre (article 1) de façon à ce
que les têtes des boulons se placent dans les contre alésages du slider de cadre.
Si le montage s'effectue sur un modèle Tuono, insérer une entretoise (article 6 – S0451) sur le
•
filetage visible de chaque boulon.
Monter l'ensemble sur la moto, en veillant à ce que la partie la plus fine du slider de cadre se place
•
contre l'avant de la moto, puis serrer les boulons jusqu'à ce que vous sentiez une légère
compression à l'intérieur du slider en utilisant une clé à cliquet + douille de 8mm. Tournez un peu
plus afin de sentir la compression augmenter légèrement. Appliquer un quart de tour. Ne pas trop
bloquer, cela pourrait endommager la partie. Ne pas excéder 40nm de couple.
Si cela n'est pas déjà fait, placer le sticker dans le creux du slider de cadre.
•
•
Placez les bouchons (article 2) dans le slider de cadre.
The catalogue description and any exhibition of samples are only broad indications of the Products and R&G may make design
changes which do not diminish their performance or visual appeal and supplying them in such state shall conform to the order. The
Buyer acknowledges no representation or warranty (other than as to title) has been given or will apply to the Products other than those
in R&G's order or confirmation and the Buyer confirms it has chosen the Products as being of merchantable quality and suitable for
its particular purposes. Where R&G fits the Products or undertakes other services it shall exercise reasonable skill and care and rectify
any fault free of charge unless the workmanship has been disturbed. The Buyer is responsible for ensuring that the warranty on the
motorcycle is not affected by the fitting of the Products. On return of any defective Products R&G shall at its option either supply a
replacement or refund the purchase money but shall not be liable if the Products have been modified or used or maintained otherwise
than in accordance with R&G's or manufacturer's instructions and good engineering practice or if the defect arises from accident or
neglect. Other than identified above and subject to R&G not limiting its liability for causing death and personal injury, it shall not be
liable for indirect or consequential loss and otherwise its liability shall be limited to the amounts paid by the Buyer for the Products or
the fitting or service concerned. These terms do not affect the Buyer's statutory rights.
Returns must be pre-authorised (if not pre-authorised the return will be rejected). Goods may only be returned direct to us if they were
purchased direct from us (customer must prove if necessary). Otherwise to be returned to original vendor. Goods must be in re-
sellable condition, in the opinion of R&G Racing. All returns are subject to a 25% restocking and handling fee (25% of the gross value
exc. P&P – at the prevailing price at time of purchase). The customer must pay any and all carriage charges. No returns of
discontinued products, unless within 14 days of purchase. This policy does not affect your statutory rights and does not refer to faulty
goods.
Tel: +44 (0)1420 89007 Fax: +44 (0)1420 87301
ISSUE 3
CONSUMER NOTICE
R&G RACING RETURNS POLICY (NON-FAULTY GOODS)
Unit 1, Shelley's Lane, East Worldham, Alton, Hampshire, GU34 3AQ
18/08/2017 (AR)
R&G Racing
www.rg-racing.com
Email:
info@rg-racing.com
Publicité
