Publicité
Les langues disponibles
Les langues disponibles
OPERATING INSTRUCTIONS
CONTROL PANEL
1. Swing and wireless connect button:
•
Press to start the auto swing feature.
•
Press and hold for three seconds to start using the
wireless connect feature.
2. Timer button: Press to set the automatic timer. Light will
indicate whether a timer is set.
3. Mode button: Press to select the desired mode. Light will
indicate current mode.
4. Temperature control buttons:
•
Press to modify the set temperature in 1° increments in
a range of 16 - 30°C (60 - 86°F).
•
Press to modify the timer setting in 0.5 hour
increments up to 10 hours and then in 1 hour
increments up to 24 hours.
•
Press and hold both temperature control buttons for
three seconds to change the temperature display from
°C to °F.
5. LED display:
•
Shows the set temperature in °C or °F.
•
Shows the timer settings.
•
Shows error codes.
•
When on fan mode, shows the room temperature.
6. Fan button:
•
Press to select fan speed. Light will indicate current
speed.
•
Press and hold for 3 seconds to turn the continuous
fan on or off.
7. Sleep and filter button:
•
Press to start the sleep feature.
•
The filter light will illuminate after 250 hours of use as
a reminder to clean the filter; to reset the filter after
cleaning, press and hold the sleep button for three
seconds.
8. Power button: Press to turn the appliance on or off.
4
2
3
1
3sec
OPERATING MODES
Cool Mode
•
Choose cool mode to set the cooling function.
•
Use the temperature control buttons to choose the desired
temperature.
•
Use the fan button to choose the desired fan speed.
•
The temperature can be set within a range of 16 - 30°C
(60 - 86°F).
•
The exhaust hose should be installed.
5
6
7
3sec
Dry Mode
•
Choose dry mode to remove excess moisture from the air.
Water will condense inside the appliance and drain out
the back.
•
The humidity level and fan speed will be automatically set
and cannot be modified in dry mode.
•
The display will show the current room temperature.
•
The exhaust hose does not need to be connected to the
window kit.
•
It may be necessary to install the continuous drain hose
during dry mode to remove excess water.
Fan Mode
•
Fan mode can be used to run the fan without engaging
the cooling or dehumidifying functions.
•
Use the fan button to choose the desired fan speed.
•
The exhaust hose does not need to be connected to the
window kit.
•
In cooling or dry mode, press and hold the fan button
for 3 seconds to set the fan to run continuously. Press
and hold the fan button for 3 seconds to disengage the
continuous fan. During normal operation the fan will turn
on and off with the compressor.
Auto Mode
Auto mode is a pre-set factory program that automatically
chooses between cool or fan mode and sets the fan speed
based on the set temperature and the ambient temperature.
The exhaust hose should be installed during auto mode.
REMOTE CONTROL
1. LED display: Shows the set temperature or the auto-timer
settings. Shows whether Follow Me is active.
2. Temperature control buttons: Used to set the temperature.
8
Press and hold both temperature control buttons for 3
seconds to change the temperature display from °C to °F.
3. Mode button: Press to select the desired mode.
4. Power button: Press to turn on or off.
5. Fan button: Press to select fan speed.
6. Swing button: Press to start the auto swing feature. When
auto swing is activated, press again to stop the louver at
the desired angle.
7. Sleep button: Press to start the sleep feature.
8. Timer on button: Press to set the automatic on timer.
9. Shortcut button: Press to set and activate the Shortcut
feature.
10. Timer off button: Press to set the automatic off timer.
11. Follow Me button: Press to activate Follow Me.
12. LED button: Press to turn the LED display on the appliance
on or off.
14
Publicité
