Stanley SW19 Mode D'emploi page 8

ENGLISH
(Original instructions)
Vehicle engines may be washed only if the dirty water is
disposed of as per regulations in force.
• Intake water temperature: See data plate on the
appliance.
• Intake water pressure: min. 0.1 MPa - max. 1 MPa.
• Operating ambient temperature: Above 0 °C.
The appliance is compliant with the IEC 60335-1 and IEC
60335-2-79 standards.
OPERATOR
The symbol illustrated in Fig. A identifies the appliance's
intended operator (professional or non-professional).
MAIN COMPONENTS (Fig. A)
1. Lance
2. Gun with safety catch
3. High pressure hose
4. Nozzle cleaning tool
5. Rotating nozzle kit
6. Nozzle
7. Adapter
8. Water filter
9. Detergent kit
10. Screws
11. Electric cable with plug
12. Wheels
13. Hose reel
14. Handle
15. Lever
16. Brackets
Starter device (19)
The starter device prevents accidental use of the appliance.
Caution! Safety devices:
Do not tamper with or adjust the safety valve setting.
• Safety valve and/or pressure limiting valve. The safety
valve is also a pressure limiting valve. When the gun
trigger is released, the valve opens and the water
recirculates through the pump inlet or is discharged onto
the ground.
• Thermostat valve (where fitted) If the water temperature
exceeds the temperature set by the manufacturer, the
thermostat valve discharges the hot water and draws in an
amount of cold water equal to the amount of water
discharged, until the correct temperature is restored.
• Safety catch (21): prevents accidental spraying of water.
• Overload cutout: stops the appliance in case of overload.
INSTALLATION (Fig. B)
Assembly
Warning! All installation and assembly operations must
be performed with the appliance disconnected from the
8
mains power supply.
The assembly sequence is illustrated in Fig. B.
Fitting the rotating nozzle
The rotating nozzle kit delivers greater washing power. Use of
the rotating nozzle may cause a reduction in pressure of 25%
compared to the pressure obtained with the adjustable nozzle.
However, the rotating nozzle kit delivers greater washing
power due to the rotation of the water jet.
Electrical connection
Warning! Check that the electrical supply voltage and
frequency (V/Hz) correspond to those on the appliance
data plate (Fig. B8).
Use of extension cables: Use cables and plugs with "IPX5"
protection level. The cross-section of the extension cable
should be pro- portionate to its length; the longer it is, the
greater its cross-section should be.
Water supply connection
Caution! Only clean or filtered water should be used for
intake. The delivery of the water intake tap should be
equal to that of pump capacity.
Place the appliance as close to the water supply system as
possible.
Connection points:
Water outlet (OUTLET)
Water inlet with filter (INLET)
Connection to the mains water supply
The appliance may only be connected directly to the mains
drinking water supply if the supply hose is fitted with a
backflow preventer valve as per current regulations in force.
Make sure that the hose is at least Ø 13 mm, that it is
reinforced and that it is not more than 25 m long.
ADJUSTMENT INFORMATION (Fig. C)
• Adjusting the spray nozzle (for models with this feature)
Water flow is adjusted by regulating the nozzle (6).
• Adjusting the detergent To deliver detergent at the correct
pressure, set the nozzle (6) on "
(9) (where available) as shown.
USE OF THE APPLIANCE (Fig. D)
Controls
Starter device (19)
Set the starter switch on (ON/I) to:
a. Start the motor (In models without TSS device);
b. Set the motor ready to start (In models with TSS device).
If there is a pilot light on the starter device, it should light up.
Set the starter device switch on (OFF/0) to stop the appliance.
" or fit the detergent kit