Publicité
LEGENDE
ARTICLE 1 = M6 ECROUS (x1)
ARTICLE 2 = M6 RONDELLES (x1)
ARTICLE 3 = BOBINES R&G (B0445) (x2)
ARTICLE 4 = ENTRETOISE GAUCHE (S1046) (x1)
ARTICLE 5 = BOULON (H0064) (x1)
ARTICLE 6 = AXE (SB125) (x1)
ARTICLE 7 = ENTRETOISE DROITE (S0368) (x1)
ARTICLE 8 = M8 RONDELLE (x1)
ARTICLE 9 = M8 ECROU (x1)
NOTICE DE MONTAGE:
•
En partant du côté gauche (assis sur la moto) insérer le boulon d'axe en utilisant une clé à cliquet + douille de
17mm.
•
Insérer un boulon R&G spécial (Article 5) dans la même position que le boulon d'origine tout juste enlevé.
Serrer à la valeur de serrage appropriée.
•
Insérer l'entretoise du côté gauche S1046 (Article 4) sur l'écrou spécial (Article 5) tout juste inséré du côté
gauche de la moto.
•
Monter une bobine R&G (Article 3), une rondelle M6 (Article 2) et un écrou M6 (Article 1) sur l'extrémité
dépassant la plus petite de l'axe (Article 5). Engager l'écrou de façon à ce que l'insert de l'écrou soit
complètement engagé.
•
Passer l'ensemble dans l'entretoise tout juste insérée sur la roue avant du côté gauche.
•
Placer l'entretoise restante (S0368 – Article 7) sur l'extrémité dépassant de l'axe pour que l'entretoise se
place sur l'écrou d'axe avant du côté droit. Ensuite, glisser la bobine R&G restante (Article 3) sur l'axe.
•
Insérer la rondelle M8 restante (Article 8) et l'écrou (Article 9) du kit sur le filetage puis serrer les 2 écrous à
l'aide d'une clé à molette + douille 13mm.
•
Ne pas trop bloquer – les écrous fixent l'ensemble.
The catalogue description and any exhibition of samples are only broad indications of the Products and R&G may make design
changes which do not diminish their performance or visual appeal and supplying them in such state shall conform to the order. The
Buyer acknowledges no representation or warranty (other than as to title) has been given or will apply to the Products other than those
in R&G's order or confirmation and the Buyer confirms it has chosen the Products as being of merchantable quality and suitable for
its particular purposes. Where R&G fits the Products or undertakes other services it shall exercise reasonable skill and care and rectify
any fault free of charge unless the workmanship has been disturbed. The Buyer is responsible for ensuring that the warranty on the
motorcycle is not affected by the fitting of the Products. On return of any defective Products R&G shall at its option either supply a
replacement or refund the purchase money but shall not be liable if the Products have been modified or used or maintained otherwise
than in accordance with R&G's or manufacturer's instructions and good engineering practice or if the defect arises from accident or
neglect. Other than identified above and subject to R&G not limiting its liability for causing death and personal injury, it shall not be
liable for indirect or consequential loss and otherwise its liability shall be limited to the amounts paid by the Buyer for the Products or
the fitting or service concerned. These terms do not affect the Buyer's statutory rights.
Returns must be pre-authorised (if not pre-authorised the return will be rejected). Goods may only be returned direct to us if they were
purchased direct from us (customer must prove if necessary). Otherwise to be returned to original vendor. Goods must be in re-
sellable condition, in the opinion of R&G Racing. All returns are subject to a 25% restocking and handling fee (25% of the gross value
exc. P&P – at the prevailing price at time of purchase). The customer must pay any and all carriage charges. No returns of
discontinued products, unless within 14 days of purchase. This policy does not affect your statutory rights and does not refer to faulty
goods.
Unit 1, Shelley's Lane, East Worldham, Alton, Hampshire, GU34 3AQ
Tel: +44 (0)1420 89007 Fax: +44 (0)1420 87301
OUTILS REQUIS
•
Clés à cliquet 2x 13mm & 17mm
•
ISSUE 1 16/06/2017 (HH)
CONSUMER NOTICE
R&G RACING RETURNS POLICY (NON-FAULTY GOODS)
R&G Racing
www.rg-racing.com
Douilles
Email:
info@rg-racing.com
FP0197BK
Publicité
