Audio Settings - Kenwood KDC-X598 Mode D'emploi

AUDIO SETTINGS

While listening to any source...
1
Press the volume knob to enter [FUNCTION].
2
Turn the volume knob to select [AUDIO CONTROL], then press the knob.
3
Turn the volume knob to make a selection (see the following table),
then press the knob.
3
Repeat step until the desired item is selected or activated.
4
Press and hold to exit.
(or using RC-406)
1
Press AUD to enter [AUDIO CONTROL].
2 Press J / K to make a selection, then press ENT IW.
To return to the previous setting item or hierarchy, press
SUB-W LEVEL –15 to +15 (0) Adjusts the subwoofer output level.
BASS LEVEL –8 to +8 (+6)
Adjusts the level to memorize for each source. (Before
MID LEVEL –8 to +8 (+5) making an adjustment, select the source you want to
adjust.)
TRE LEVEL –8 to +8 (0)
KDC-X598
EQ PRO (for )
BASS ADJUST BASS CTR FRQ 60/ 80/ 100/ 200HZ: Selects the center frequency.
BASS LEVEL –8 to +8 (+6): Adjusts the level.
BASS Q FACTOR 1.00/ 1.25/ 1.50/ 2.00: Adjusts the quality factor.
BASS EXTEND ON: Turns on the extended bass. ; OFF: Cancels.
MID ADJUST MID CTR FRQ 0.5/ 1.0/ 1.5/ 2.5KHZ: Selects the center frequency.
MID LEVEL –8 to +8 (+5): Adjusts the level.
MID Q FACTOR 0.75/ 1.00/ 1.25: Adjusts the quality factor.
TRE ADJUST TRE CTR FRQ 10.0/ 12.5/ 15.0/ 17.5KHZ: Selects the center frequency.
TRE LEVEL –8 to +8 (0): Adjusts the level.
PRESET EQ
BASS BOOST
LOUDNESS
.
SUBWOOFER SET
LPF SUBWOOFER
Default: XX
SUB-W PHASE
HPF
FADER
BALANCE
VOLUME OFFSET
(Default: 0)
SOUND RECNSTR
(Sound
reconstruction)
[SUB-W LEVEL]/ [LPF SUBWOOFER]/ [SUB-W PHASE] is selectable only if
[SUBWOOFER SET] is set to [ON].
DRIVE EQ/ TOP40/ POWERFUL/ ROCK/ POPS/ EASY/ JAZZ/
NATURAL/ USER: Selects a preset equalizer suitable to the music
genre. (Select [USER] to use the customized bass, middle, and treble
settings.)
[DRIVE EQ] is a preset equalizer that reduces noise from the road.
/ /
LEVEL1 LEVEL2 LEVEL3: Selects your preferred bass boost level. ;
OFF: Cancels.
LEVEL1/ LEVEL2: Selects your preferred low and high frequencies
boost to produce a well-balanced sound at a low volume level. ;
OFF: Cancels.
ON: Turns on the subwoofer output. ; OFF: Cancels.
THROUGH: All signals are sent to the subwoofer. ; 85HZ/ 120HZ/
160HZ: Audio signals with frequencies lower than 85 Hz/ 120 Hz/
160 Hz are sent to the subwoofer.
REVERSE (180°)/ NORMAL (0°): Selects the phase of the subwoofer
output to be in line with the speaker output for optimum performance.
(Selectable only if a setting other than [THROUGH] is selected for
[LPF SUBWOOFER].)
THROUGH: All signals are sent to the speakers. ; 100HZ/ 120HZ/
150HZ: Audio signals with frequencies higher than 100 Hz/ 120 Hz/
150 Hz are sent to the speakers.
R15 to F15 (0): Adjusts the rear and front speaker output balance.
L15 to R15 (0): Adjusts the left and right speaker output balance.
–8 to +8 (for AUX) ; –8 to 0 (for other sources): Presets the volume
adjustment level of each source. (Before adjustment, select the source
you want to adjust.)
ON: Creates realistic sound by compensating the high-frequency
components and restoring the rise-time of the waveform that are lost
in audio data compression. ; OFF: Cancels.
ENGLISH | 17