JVC TK-C655 Instructions page 41

AUTO RETURN Setup
If the camera is not operated at the preset time after it has been operated manually, it will automatically return to the status set
previously.
< RM-P2580 rear >
TO CAMERA TO CAMERA DATA I / O DATA I / O
RX+ RX RX RX- TX TX+ TX TX-
COM COM 1 2 3 4 5 6 7 8 COM 9/1 10/2 11/3 12/4 13/5 14/6 15/7 16/8 COM COM
POWER
ON OFF
1 2 3 4
AC ` INPUT
1 2 3 4 5 6 7 8
1 2 3 4
ON
1 2 3 4
ON
MENU button
SET button
REMOTE CONTROL UNIT
CAMERA POSITION
SETUP POWER
ALARM
MENU SET AUTO
KEY LOCK
LENS CAMERA/POSITION
1 2 3
CAMERA POSI-
SPEED
TION
4 5 6
CLOSE IRIS OPEN OPTION OPTION
1 2
FOCUS
7 8 9 AUTO AUTO
NEAR FAR
AF
PAN PATROL
0
WIDE ZOOM TELE CLEAR ENTER
/HOME
ENTER button
– – – M E N U – – –
C A M . F U N C T I O N 1 . .
C A M . F U N C T I O N 2 . .
C A M . T I T L E / A L A R M . .
C A M . V I D E O A D J U S T . .
C A M . A L C . .
H O M E M O T I O N D E T E C T . .
A U T O P A N / P A T R O L / T R A C E . .
P O S I . F U N C T I O N S E T . .
F A C T O R Y S E T T I N G S . .
SETUP menu display on the camera
– – – C A M E R A F U N C T I O N 2 – – –
A F F O R I R O F F
A U T O R E T U R N O F F
R E T U R N T I M E – – –
CAMERA FUNCTION2 screen
UNIT UNIT CAMERA CAMERA SERIAL-1 SERIAL-1 SERIAL-2 SERIAL-2
COM AUTO ALARM ALARM COM COM SW COM COM
VIDEO INPUT VIDEO INPUT
5 6 7 8
MONITOR MONITOR MONITOR MONITOR
OUTPUT OUTPUT OUTPUT OUTPUT
1 2
5 6 7
8
VIDEO OUTPUT VIDEO OUTPUT
5 6 7 8
RM-P2580
F-1 F-2 F-3
CAMERA
PAN/TILT buttons
PAN/TILT
lever
*Before setting AUTO RETURN, make sure to set the
rear panel DIP Switch of RM-P2580.
1. Turn off the power of RM-P2580.
2. Set rear DIP Switch4 of RM-P2580 to "ON".
3. Turn on the power of RM-P2580 again.
1.
Display the SETUP menu on the camera.
☞
( P.20, steps 1 to 4)
• MENU button(3sec) → Select "CAMERA" with the PAN/TILT lever
→ SET button.
2.
Display the CAMERA FUNCTION2 screen.
• Tilt the PAN/TILT lever up or down to move the cursor (>) to "CAM-
ERA FUNCTION2" and press the SET button.
• The CAMERA FUNCTION2 screen is displayed.
3.
Set the return status using AUTO RETURN function.
• Set the status for the camera to return to automatically when it is not
operated for a certain time.
• Setting values: OFF, HOME, A.PAN KEY, A.PATROL KEY
4.
Set the time for AUTO RETURN to activate.
• Selectable time: 1 min, 2 min, 3 min, 5 min, 10 min, 20 min, 30
min, 60 min
• When "AUTO RETURN" is set to "OFF", "---" will be displayed and
setting will be disabled.
5.
Press the MENU button.
The screen returns to the MENU screen.
MEMO
●
During MENU setting and alarm operation, it will not return to the status set
under AUTO RETURN.
●
After the alarm operation, it will return to the status set under AUTO RE-
TURN.
●
When using AUTO RETURN function, make sure to use the REMOTE CON-
TROL UNIT of the product with model name RM-P2580(A) as on the serial
number plate. RM-P2580 without (A) will not function properly.
E-41