Publicité
Les langues disponibles
Les langues disponibles
1. To maximize flush cutting capabilities, insert the blade
shaft into the blade clamp with the teeth of the blade
facing up.
2. Position the saw to make the flush cut so you are as close
to the work surface as possible.
Wood Cutting (Fig. G)
1. Before cutting any type of wood, be sure the workpiece
is firmly anchored or clamped to prevent slipping.
2. Place blade and pivoting shoe firmly against work
to be cut.
3. Switch on saw motor before starting the cut.
4. Always hold saw as shown in Fig. G while cutting.
Whenever possible, the pivoting shoe must be held firmly
against the material being cut. This will prevent the saw
from jumping or vibrating and minimize blade breakage.
Metal Cutting (Fig. H)
1. Use a finer blade for ferrous metals and a coarse blade for
non-ferrous materials.
2. In thin gauge sheet metals it is best to clamp wood
to the underside of the sheet. This will ensure a clean cut
without excess vibration or tearing of metal.
3. Avoid forcing cutting blade as this reduces blade life and
causes costly blade breakage.
nOTE: You should spread a thin film of oil or other coolant
along the line ahead of the saw cut for easier operation
and longer blade life. For cutting aluminum, kerosene
is preferred.
Pocket Cutting ‑ Wood Only (Fig. I)
Measure the surface area to be cut and mark clearly with a
pencil, chalk or scriber.
1. Insert blade in blade clamp.
2. Tip the saw backward until the back edge of the pivoting
shoe is firmly on the work surface.
3. Switch motor on, permitting blade to attain
maximum speed.
4. Grip handle steadily and begin a slow, deliberate upward
swing with the handle of the saw.
5. The blade will begin to feed into material. Always be sure
blade is completely through material before continuing
with pocket cut.
nOTE: In areas where blade visibility is limited, use the edge
of the pivoting shoe as a guide.
Project Tips
• Cut only with sharp blades; they cut cleaner, faster and
put less strain on the motor while cutting.
• When cutting, always ensure that the pivoting shoe is
resting against the workpiece. This will improve operator
control and minimize vibration.
• For longer blade life, use bi-metal or carbide tipped
blades. These utilize a carbon steel back welded to high
speed steel teeth making the blade more flexible and less
prone to breaking.
MAINTENANCE
WARNING: To reduce the risk of serious personal
injury, turn unit off and remove the battery pack
before making any adjustments or removing/installing
attachments or accessories. An accidental start-up can
cause injury.
Your D
WALT power tool has been designed to operate
e
over a long period of time with a minimum of maintenance.
Continuous satisfactory operation depends upon proper
tool care and regular cleaning.
Cleaning
WARNING: Blow dirt and dust out of all air vents with
clean, dry air at least once a week. To minimize the risk of eye
injury, always wear ANSI Z87.1 approved eye protection when
performing this procedure.
WARNING: Never use solvents or other harsh chemicals
for cleaning the non-metallic parts of the tool. These
chemicals may weaken the plastic materials used in these
parts. Use a cloth dampened only with water and mild soap.
Never let any liquid get inside the tool; never immerse any part
of the tool into a liquid.
Accessories
WARNING: Since accessories, other than those offered by
D
WALT, have not been tested with this product, use of such
e
accessories with this product could be hazardous. To reduce
the risk of injury, only D
WALT recommended accessories
e
should be used with this product.
Recommended accessories for use with your product are
available at extra cost from your local dealer or authorized
service center. If you need assistance in locating any
accessory, please contact D
(1‑800‑433‑9258) or visit our website: www.dewalt.com.
Repairs
The charger and batteries are not serviceable. There are no
serviceable parts inside the charger or battery pack.
WARNING: To assure product SAFETY and RELIABILITY,
repairs, maintenance and adjustment (including brush
inspection and replacement, when applicable) should be
performed by a factory service center or an authorized service
center. Always use identical replacement parts.
Register Online
Thank you for your purchase. Register your product now for:
• WARRAnTY sERViCE: Registering your product will help
you obtain more efficient warranty service in case there is a
problem with your product.
• COnFiRMATiOn OF OWnERshiP: In case of an
insurance loss, such as fire, flood or theft, your registration of
ownership will serve as your proof of purchase.
• FOR YOUR sAFETY: Registering your product will allow
us to contact you in the unlikely event a safety notification is
required under the Federal Consumer Safety Act.
• Register online at www.dewalt.com.
Three‑Year Limited Warranty
For warranty terms, go to
www.dewalt.com/support/warranty.
To request a written copy of the warranty terms, contact:
Customer Service at D
WALT Industrial Tool Co., 701 East
e
Joppa Road, Towson, MD 21286 or call 1‑800‑4‑D
(1‑800‑433‑9258).
lATin AMERiCA: This warranty does not apply to products
sold in Latin America. For products sold in Latin America,
see country-specific warranty information contained in
the packaging, call the local company or see website for
warranty information.
English
WALT. Call 1‑800‑4‑D
WALT
e
e
WALT
e
7
Publicité
