Publicité
Les langues disponibles
Les langues disponibles
Safety Chain
The cooker is fitted with a safety chain to be fixed by
means of a screw (not supplied with the cooker) to the
wall behind the appliance, at the same height as the
chain is attached to the appliance.
Choose the screw and the screw anchor according
to the type of material of the wall behind the appliance.
If the head of the screw has a diameter smaller than
9mm, a washer should be used. Concrete wall requires
the screw of at least 8mm of diameter, and 60mm of length.
Ensure that the chain is fixed to the rear wall of the cooker
and to the wall, as shown in figure, so that after installation
it is tensioned and parallel to the ground level.
Gas connection
The cooker should be connected to the gas-supply by a
gas safe registered installer. During installation of this
product it is essential to fit an approved gas tap to isolate
the supply from the appliance for the convenience of any
subsequent removal or servicing. Connection of the
appliance to the gas mains or liquid gas must be carried
out according to the prescribed regulation in force, and
only after it is ascertained that it is adaptable to the type
of gas to be used. If not, follow the instructions indicated
in the paragraph headed "Adaptation to different gas types".
On some models the gas supply can be connected on the
left or on the right, as necessary; to change the connection,
reverse the position of the hose holder with that of the cap
and replace the gasket (supplied with the appliance). In the
case of connection to liquid gas, by tank, use pressure
regulators that conform to the regulation in force. The gas
supply must be connected to the left of the appliance.
Be sure that the hose does not pass through the rear of the
cooker touching hot parts.
Table of burner and nozzle specifications
Burner
Rapid (R)
Semi Rapid
(Medium) (S)
Auxiliary
(Small)
(A)
Supply
Pressures
*with dry gas 15°C 1013 mbar
** Propane P.C.S=50,37 MJ/Kg
*** Butane P.C.S=49,47MJ/kg
Natural G20 P.C.S=37,78Mj/m³
In order to prevent
accidental tipping
of the appliance,
for example by
a child climbing
onto the oven door,
the supplied safety
chain MUST be
installed!
Thermal Power
kW (p.c.s*)
Diameter (mm) Nominal Reduced
100
3.00
0.70
75
2.00
0.40
55
1.00
0.40
Nominal (mbar)
Minimum (mbar)
Maximum
Adapting to different types of gas
It is possible to adapt the appliance to a type of gas other than the
default type (this is indicated on the rating label on the cover).
Adapting the hob
3. Replace all the components by following the above instructions
in reverse.
Adjusting the hob burners' minimum setting:
1. Turn the tap to the minimum position.
2. Remove the knob and adjust the regulatory screw, which is
positioned inside or next to the tap pin, until the flame is small
but steady. If the appliance is connected to a liquid gas supply,
the bypass screw must be set to a minimum.
3. While the burner is alight, quickly change the position of the
knob from minimum to maximum and vice versa several times,
checking that the flame is not extinguished.
Upon completion of adjustment, reseal using sealingwax or an
equivalent material.
The hob burners do not require primary air adjustment.
After adjusting the appliance so it may be used with a different type
of gas, replace the old rating label with anew one which corresponds
to the new type of gas (these labels are available from Authorised
Technical Assistance Centres).
Should the gas pressure used be different (or vary slightly) from
the recommended pressure, a suitable pressure regulator must be
fitted to the inlet hose in accordance with current standards EN
88-1 and EN 88-2 relating to "regulators for channelled gas".
Liquid Gas
Flow
g/h
Nozzle
By-Pass 1/100
1/100
(mm)
(mm)
***
41
86
218
30
70
145
30
50
73
28-30
20
35
24
Replacing the nozzles for the hob burners:
1. Remove the hob grids and slide the burners
off their seats.
2. Unscrew the nozzles using a 7mm socket
spanner (see figure), and replace them with
nozzles suited to the new type of gas
(see Burner and nozzle specifications table).
Natural Gas
G20
Nozzle
Nozzle
1/100
Flow
1/100
**
(mm)
g/h
(mm)
214
116
286
125 F3
143
103
190
100 Y
71
79
95
72 F1
37
25
45
G25
Flow
g/h
332
211
111
25
20
30
Publicité
