Télécharger Imprimer la page

Bosch NGM8659UC Instructions D'installation page 7

Masquer les pouces Voir aussi pour NGM8659UC:

Publicité

Les langues disponibles

Les langues disponibles

2 Before you begin
Before you begin
This Installation Instructions covers several models. All
Before you begin
graphics are representative. Your appliance may vary in
appearance and features.
2.1 Parts included
After unpacking all the parts, check for any damage in
transit and for completeness of delivery.
¡ Cooktop
¡ Foam tape
¡ Hold-down brackets (4)
¡ Screws, #10-32 x 2½" (63.8 mm), (4)
¡ Sheet metal screws, #8 x 3/8" (9.5 mm), (4)
¡ Washers (4)
¡ Burner grates (3)
¡ Burners (5)
¡ Burner caps (6)
¡ Pressure regulator
¡ LP gas conversion kit
2.2 Tools and parts needed
Prepare these tools and accessories before you start to
install your appliance.
¡ Pencil
¡ Measuring tape
¡ Cross head screwdriver
¡ Drill with bit 1/4" (6 mm)
¡ Jigsaw
¡ Adjustable wrench
¡ Teflon® tape - gas rated
¡ Flathead screwdriver, 1/8"
Additional tools needed for LP gas conversion
¡ 7 mm socket wrench
¡ 7 mm open end wrench
¡ T10 star bit screwdriver
¡ T20 star bit screwdriver
¡ Small piece of tape
Note: Additional materials may be necessary for
installation in solid surface countertops. Contact the
countertop manufacturer.
2.3 General requirements
Ensure that the following requirements are met when
planning the installation of your appliance.
¡ Plan the installation of the unit so that the power cord,
gas shut-off valve and gas pressure regulator are
accessible from the front of the cabinet.
¡ Make sure the gas supply line does not interfere with
the back of the appliance.
¡ The cabinet in which the cooktop is installed must be
properly secured, level and stable.
¡ Any laminated coverings and glue on cabinets next to
the cooktop must be made of non-flammable and heat
resistant materials. Refer to local building codes for
acceptable materials.
¡ This appliance cannot be installed above refrigerators,
washing machines, dishwashers or similar.
¡ If the cooktop will be installed in combination with an
oven, refer to the Approved Combination Matrix
included with the product for cutout and clearance
dimensions.
2.4 Cabinet requirements
Ensure that the cabinetry at the installation location meets
the requirements for a safe installation.
The minimum spaces that must be maintained when
installing the gas cooktop shall be the following:
a
min. 13" (330 mm)
for installation next to oven min. 13" (330 mm)
b
min. 13" (330 mm)
for installation next to oven min. 13" (330 mm)
c
min. 30" (762 mm) clearance between the top of
the cooking surface and the bottom of combustible
constructions
d
min 3" (76 mm);
for installation in kitchen islands, min. 4" (100 mm)
e
For 30" cooktops:
min. 30" (760 mm) centered over cooktop
e
For 36" cooktops:
min. 36" (914 mm) centered over cooktop
f
min. 18" (458 mm)
g
max. 13" (330 mm)
h
min. 1¾" (48 mm);
for installation in kitchen islands, min. 4" (100 mm)
Before you begin en-us
7

Publicité

loading

Ce manuel est également adapté pour:

Ngm8059uc