Publicité
Les langues disponibles
Les langues disponibles
Installing your refrigerator,
How to connect the
water supply
WARNING
To reduce the risk of injury or
death, follow basic precautions,
including the following:
Read
all
instructions
installing device.
DO NOT attempt installation if
instructions are not understood or if
they are beyond personal skill
level.
Observe all local codes and ordi-
nances.
DO NOT service device unless
specifically
recommended
owner's manual or published user-
repair instructions.
Disconnect power to unit prior to
installing device.
CAUTION
To avoid property damage or possi-
ble injury, follow basic precautions,
including the following:
Consult a plumber to connect
copper tubing to household plumb-
ing to assure compliance with local
codes and ordinances.
Confirm water pressure to water
valve is between 20 and 100
pounds per square inch. If water
filter is installed, water pressure to
water valve must be a minimum of
35 pounds per square inch.
DO NOT use a self-piercing, or
" saddle valve! Both reduce
3
⁄
16
water flow, become clogged with
time, and may cause leaks if repair
is attempted.
Tighten nuts by hand to prevent
cross threading. Finish tightening
nuts with pliers and wrenches. Do
not overtighten.
Wait 24 hours before placing unit
into final position to check and
correct any water leaks.
8
All manuals and user guides at all-guides.com
MATERIALS NEEDED
1
" outer diameter flexible copper
Ú
4
tubing
Shut-off valve (requires a
drilled into water supply before valve
attachment)
Adjustable wrench
1
" hex head driver
Ú
4
before
NOTE: Add 8' to tubing length needed to
reach water supply for creation of service
loop.
1. Create service loop
with tubing using
care to avoid kinks in
tubing.
in
2. Remove plastic cap (A)
from water valve inlet
port (B).
3. Place brass nut
(D) and sleeve
(E) on copper
tube
end
illustrated.
4. Place end of copper tub-
ing into water valve inlet
port.
Shape
slightly – DO NOT KINK –
so that tubing feeds
straight into inlet port.
5. Slide brass nut over sleeve
and screw nut into inlet port.
Tighten nut with wrench.
IMPORTANT: DO NOT overtight-
en. Cross threading may occur.
6. Pull on tubing to confirm
connection
Connect tubing to frame
with water tubing clamp (F)
and turn on water supply.
Check
for
correct, if present.
7. Monitor water connection for 24 hours.
Correct leaks, if necessary.
cont.
" hole to be
1
Ú
4
B
B
A
A
D
E
as
tubing
F
is
secure.
leaks
and
How to level your
refrigerator
If your refrigerator requires an ice maker
water supply connection, proceed to How
to connect the water supply section
before leveling your refrigerator.
CAUTION
To protect personal property or unit
from damage, observe the following:
Protect soft vinyl or other flooring
with cardboard, rugs, or other
protective material.
Do not use power tools when
performing leveling procedure.
MATERIALS NEEDED
" hex head driver
3
Ú
8
Level
1. Move refrigerator to final location and
plug in power cord.
2. Remove toe grille
and
bottom
cover(s).
3. Turn left and right adjust-
ment screws (A) to
raise or lower front
of refrigerator.
• Make sure refriger-
ator cabinet is level
from side to side by
adjusting left and
right roller adjustment screws.
• Turn stabilizing leg clockwise until
firmly against floor.
For Pullout Drawer Models: After
completing the above listed steps, turn
roller adjustment screws (A) 2 to 3 times
counterclockwise, so that full weight of
unit rests on stabilizing legs.
4. Using a level, make sure front of
refrigerator is
1
" (6 mm) or
Ú
4
higher than back of refrigerator.
• See leveling step 3 for assistance.
A
1
bubble
Ú
2
Publicité
