Solo 620 Instructions D'emploi page 12

Table des Matières

Publicité

Les langues disponibles
  • FR

Les langues disponibles

  • FRANÇAIS, page 17
Introduction to the Operating Instructions
These Operating Instructions are intended to facilitate your becoming acquainted with the machine and using it in
accordance with the regulations. The Operating Instructions contain important information on how to use the
machine safely, correctly and economically. Observing this information will help increase the reliability and
working life of the machine. The Operating Instructions must always be at hand when the machine is being used.
They must be read and observed by every person dealing with the machine, whether operating, servicing or
transporting it.
In addition to the Operating Instructions and the applicable rules of the prevention of accidents valid in the country
of use and on site, the generally recognised rules on working safely and correctly must be observed as well as the
accident prevention rules of the relevant professional associations.
Technical Data
This chain saw has been built in accordance with Regulation DIN EN 50144-2-13 and fulfils the requirements of the
European law on equipment safety.
Model
Rated Voltage
Nominal Frequency
50Fuse (time lag)
Rated Output
Nominal current
Guide Bar
Speed
Weight
Oil
All models with automatic chain lubrication and mechanical chain brake and rundown brake.
The type designation of the chain you will find on the type plate.
Class of Protection:
Interference Suppression:
Information on noise emission in accordance with the 3rd Decree on the German law on equipment safety of 18.1.1991
and the EU Guideline on machines, Appendix I, Section 1.7.4 f.
Noise emission values EN-50144-2-13:
Vibration values in accordance with EN 50144-2-13:
Attention: This chain saw is only intended for cutting wood !!!
Important instructions for your personal safety
A) General safety instructions
Attention: You run danger of injuring yourself if
you use the chain saw incorrectly. It is imperative
that you read these Operating Instructions and follow
the instructions given.
Attention: Noise protection ! Please observe the local
regulations when operating your device.
1. Caution! : When electric tools are being used, the
following basic safety measures must be taken to
protect against electric shock, injury and risk of fire.
2. Protect yourself against electric shock. Avoid body
contact with grounded elements, e.g. pipes, radiators,
stoves, refrigerators.
3. Children and young persons under 18 may not
operate electrical chain saws, with the exception of
apprentices older than 16 under the supervision of a
trained adult.
4. The chain saw may only be used by persons who
have sufficient experience.
5. Always keep these Operating Instructions together
with the chain saw.
6. Only lend or give this chain saw to persons who
V~
Hz
A
W
A
cm
m/sec
kg
ml
II/ DIN-EN 50144/ VDE 0740
nach EN-55014
Solo 620
230
50
16
2000
9,4
40
ca. 11
4,4
200
Sound Pressure Level L pA
Weighted acceleration handle
are familiar with its use. Also give them these
Operating Instructions.
7. You should always be in a good physical state when
working with the chain saw. Work steadily and with
concentration. Particular concentration is necessary
towards the end of your duty.
8. Never use the chain saw while under the influence of
alcohol, medication or drugs.
B) Instructions on the use of personal protective
clothing
Working with a chain saw requires special measures with
regard to protective equipment and clothing suitable for
protecting your head, hands, feet and legs, eyes and
ears.
9. Wear close fitting clothing which cannot get caught
10. Always wear an approved and tested safety helmet
when felling trees and removing branches.
11. Always wear safety goggles or a face guard.
12. Always wear suitable protective gloves.
13. Wear ear protection to avoid damage to your
hearing.
14. Wear safety boots.
15. We recommend that you wear leg guards.
GB-1
ENGLISH
93 dB (A)
max. 11 m/s 2

Publicité

Table des Matières
loading

Table des Matières