Publicité
Les langues disponibles
Les langues disponibles
scribed below must be carried
out:
Set the appliance switch to
"I".
Open the water supply.
Start cleaning (see "Care and
Maintenance/Chemical
cleaning").
ATTENTION
Damage to the device cooling
unit.
If the device has been stored
or transported lying down,
you must place the device in
its normal position and then
wait at least 24 hours before
operating it.
Environmental protection
The packaging material can be recycled.
Please do not throw the packaging mate-
rial into household waste; please send it
for recycling.
Old appliances contain valuable materials
that can be recycled; these should be sent
for recycling. Batteries, oil, and similar
substances must not enter the environ-
ment. Please dispose of your old appli-
ances using appropriate collection sys-
tems.
Electrical and electronic devices often contain compo-
nents which could potentially pose a danger to human
health and the environment if handled or disposed of
incorrectly. However, these components are necessary
for the proper operation of the device. Devices marked
with this symbol must not be disposed of with regular
household rubbish.
R-290 Contains greenhouse gas R290 - hermetically
sealed device.
Notes about the ingredients (REACH)
You will find current information about the ingredients
at:
www.kaercher.com/REACH
Transport
CAUTION
Mind the weight of the appliance during transport.
Do not transport the device horizontally.
Due to its weight, the WPD 200 should be assem-
bled by two persons or with the aid of appropriate
aids such as a sack truck.
Proper use
This device is not designed to be used by persons
(including children) with restricted physical, senso-
ry or mental abilities or those lacking in experience
and/or lacking in knowledge except where they are
supervised by a person responsible for their safety
or else have been instructed by them in how to use
the device and have understood the resultant dan-
gers. Cleaning and user maintenance may not be
carried out by unsupervised children. Children
must be supervised to prevent them from playing
with the device.
The device is used to dispense tempered and un-
tempered drinking water of approved food quality in
self-service operations. Depending on the device
model, the water dispenser is equipped with differ-
ent filters (Active Pure filter or Hy Protect filter).
This device is intended for use in domestic and
similar applications, such as staff kitchen areas in
shops, offices and other work areas, in agriculture
and by guests in hotels, motels and other accom-
modations as well as in catering and similar large-
scale use.
The appliance must be installed in frost-free rooms.
Do not use or park the device outdoors.
Do not lay down the device or store or transport it
in a horizontal position.
Function
Water first flows from the water inlet through the filters
(for filter description see consumables). Depending on
the button pressed, the water then flows through the
cooling module, the CO2 mixer (depending on equip-
ment) or directly to the water dispenser.
When carbonated water is required (option), the water
(option) will be enriched with carbon dioxide.
The entire water system must be chemically cleaned at
regular intervals.
Connecting the appliance
Preconditions
DANGER
Should it be necessary to open the side parts for the in-
stallation and initial startup of the device, this may only
be done by a qualified electrician.
During the initial installation and in case of repairs,
which involve the replacement of accessories, you
must make sure that only the components defined
as accessories are used (connection kit, CO
sure regulator (option, appliance with CO
parts are components that have been released by
KÄRCHER for installation. These components are
tested and certified to meet the high quality require-
ments of the certification by the SGS Institut Frese-
nius GmbH and the KÄRCHER quality standards.
Never use other components.
The power connection and the water input pres-
sure must conform to the data in the specifications.
Depending on local regulations, the use of an ap-
proved check valve is required.
Devices with a drip pan drain into the waste water
line of the building must be designed with a trap for
the protection against unpleasant odour from the
waste water line.
The trap must be positioned lower than the drip
pan.
Only with a continuously falling waste water hose
the drip pan drain works in a reliable way.
There must be an even surface available to install
the appliance.
Power plug and receptacle must be freely accessi-
ble after the installation.
In the interest of reducing power consumption, the
power supply can be switched off when the device
is not in use (e.g. using a timer clock):
Power switch, fuse and water connection at the
back of the device must be freely accessible. The
minimum distance to the wall is 100 mm.
Only for WPD 200 with stand:
In order to guarantee a great stability of the device
in accordance with the provisions of the device
standard, a device with base must be secured on
the floor or wall (attachment kit floor fixing WPD
2.643-483.0).
As an alternative, the attachment kit additional
weight for base WPD (2.643-474.0) can be used in
order to lower the centre of gravity of the device ac-
cordingly.
2
-
EN
pres-
2
). These
2
1
Water supply line
2
Check valve**
3
Pressure reducer**
4
Aqua stop *
5
Water faucet *
6
Drinking water supply *
7
Wastewater line *
8
Facility power supply *
9
Socket, protected via error current protective
switch 30 mA *
10 Connecting cable
11 WPD 200***
12 Drain of drip pan ***
13 Trap**
* on site, not included in the scope of delivery
** optional, not included in the scope of delivery
*** optional, depending on the device configuration
Establishing connection
1
Inlet sieve
2
Water connection (connection thread 3/4")
3
Main Supply
4
Drip pan drain (optional)
Device without drip pan drain
With this device design no drain hoses need to be in-
stalled.
Device without base, with drip pan drain
Connect the hose to the drip pan drain and install it
to the siphon or to the can.
Device with base and drip pan drain
Use an elbow to connect the hose to the drip pan
drain and install it through the base to the siphon or
to the can.
All device designs
Connect the water supply hose to the water con-
nection (connection thread 3/4") at the back of the
device.
Connect power cable with the power supply on the
back of the device.
Insert the mains plug into the socket.
15
Publicité
