Publicité
Les langues disponibles
Les langues disponibles
Active AX
|
Operation
4)
Check that the filters are correctly fitted. [Fig. 3]
5)
T urn on the machine.
2.7
General machine settings
2.7.1
Initial Settings
Temperature settings
1)
To enter the temperature settings section, when turning on the
machine, press and hold the PROG button
seconds while the program is loading.
2)
P ress the START button
– Tank temperature settings
– B oiler temperature settings
Tank temperature settings (washing)
1)
T he
icon lights up and one of the program/cycle icons
flashes. Each symbol represents a tank temperature as shown
in the following table:
Icon flashes
Tank temperature
Disconnection of elements (room
temperature)
50 °C
60 °C60 °C
65 °C
2)
T o select the tank temperature, press the PROG button
⇒
A fter 3 seconds without pressing the PROG button
temperature is selected and the cycle led stops flashing.
3)
T o confirm the machine, press the ON/OFF button.
⇒
T he machine shuts down.
Boiler temperature settings (rinsing)
1)
T he
icon lights up and one of the program/cycle icons
flashes. Each symbol represents a tank temperature as shown
in the following table:
Icon flashes
Boiler temperature
Disconnection of elements (room
temperature)
75 °C
80 °C
85 °C
2)
T o select the tank temperature, press the PROG button
⇒
A fter 3 seconds without pressing the PROG button
temperature is selected and the cycle led stops flashing.
3)
T o confirm the machine, press the ON/OFF button.
⇒
T he machine shuts down.
Thermal lock
If the thermal lock function is activated:
•
I f you press the START button
•
T he icon
lights up when the boiler has not yet reached the
setpoint temperature at the time of rinsing. The wash pump
continues to run until the boiler reaches its pre-set temperature.
6
in the first two
to choose between the icons:
(washing).
(rinsing).
.
, the
.
, the
, the cycle cannot advance.
To activate the Thermal lockfunction:
1)
S witch the appliance on by pressing the ON/OFF button.
2)
T o activate this function, access the electronic board and set
switch 1 to position 1. See the SW1 position last figure in the
appendix at the end of the manual.
2.7.2
Auto start settings
The "auto start" option allows the machine to start the wash cycle
automatically when the door/dome is closed.
To enable/disable the "auto start" option:
1)
W ith the door/dome open, press the START button
⇒
I con
on: auto start enabled.
⇒
I con
auto start disabled.
off:
2.7.3
Model settings
If the electronic board is changed or de-configured, the machine
requires the model to be adjusted by means of the following adjust-
ment section:
1)
T o access the electronic board, turn off the machine: press the
ON/OFF button.
2)
To activate this function, access the control board and set
switches 2-5 to position 1 or position 0 as shown in the table
below. See the SW1 position last figure in the appendix at the
end of the manual.
No.
SW-
SW-
SW-
SW-
2
3
4
5
17–
0
0
0
1
18
19–
1
0
0
1
20
13–
0
1
1
0
14
15–
1
1
1
0
16
17–
0
0
0
1
18
19–
1
0
0
1
20
21–
0
1
0
1
22
23–
1
1
0
1
24
[*] Optional for cycles of 90/120/180.
3
Operation
⚠ W a rn in g
Risk of serious injury due to operation when the
machine is faulty
Using the machine when it is faulty or in poor condition can af-
fect personal safety and damage the machine.
– If you detect any fault or anomaly in the machine, contact an
authorised service agent immediately.
.
Model
Models
Drain
pump
AX-40
Glass-
NO
washer 3
cycles
AX-40/B
YES
AX-40 [*]
Glass-
NO
washer 3
cycles
AX-40/B[*]
YES
AX-50
Dish-
NO
washer 3
cycles
AX-50/B
YES
AX-100
3-cycle
NO
hood
AX-100/B
YES
User's manual — 2900453/2
Publicité
