Publicité
Les langues disponibles
Les langues disponibles
How to make the batteries perform longer.
(1) Recharge the batteries before they become completely
exhausted.
When you feel that the power of the tool becomes
weaker, stop using the tool and recharge its battery. If
you continue to use the tool and exhaust the electric
current, the battery may be damaged and its life will
become shorter.
(2) Avoid recharging at high temperatures.
A rechargeable battery will be hot immediately after
use. If such a battery is recharged immediately after
use, its internal chemical substance will deteriorate, and
the battery life will be shortened. Leave the battery and
recharge it after it has cooled for a while.
CAUTION
○ If the battery is charged while it is heated because
it has been left for a long time in a location subject to
direct sunlight or because the battery has just been
used, the charge indicator lamp of the charger lights
for 0.3 seconds, does not light for 0.3 seconds (off for
0.3 seconds). In such a case, fi rst let the battery cool,
then start charging.
○ When the charge indicator lamp fl ickers (at 0.2-second
intervals), check for and take out any foreign objects in
the charger's battery connector. If there are no foreign
objects, it is probable that the battery or charger is
malfunctioning. Take it to your authorized Service
Center.
MOUNTING AND OPERATION
Action
Removing and inserting the battery
Charging
Adjusting operating speed*
Switch operation*
2
How to use the LED light
How to use the hook*
3
Removing the holder
Exchanging the rack (push-out rod)*
Types of pistons*
5
Exchanging the piston*
6
Attaching the 300 ml holder
Attaching the 400 ml/600 ml holder
Using cartridges*
7
Using sausages*
7
Using buckets*
7
Temporarily setting down the tool
while working*
8
Removing hardened sealing
material*
9
Remaining battery indicator
Charging a USB device from a
electrical outlet
Charging a USB device and battery
from a electrical outlet
Figure
Page
3
2
4
2
5
2
1
6
3
7
3
8
3
9
3
10
4
4
11
4
12
4
13-a
4
13-b
4
14
5
15
5
16
5
17
6
18
6
19
6
20-a
6
20-b
6
How to recharge USB device
When charging of USB device is
completed
Selecting accessories
*1 Adjusting operating speed
This can be performed even while working. Adjust the
speed together with the amount that the switch is pulled.
CAUTION
If the diameter of the cross section of the nozzle is 3 mm
or smaller, or if there is an attempt to abruptly dispense
at high speed while under low-temperature conditions,
the sealing material may leak out on the piston side.
Begin at low speed, and gradually increase speed to suit
the hardness of the sealing material.
*2 Switch operation
Immediately after the switch is released, the piston
retracts slightly to prevent sealing material remaining at
the end of the nozzle from dripping.
*3 How to use the Hook
The hook can be used to hang up the unit
temporarilyduring operations.
CAUTION
The hook should never be used to hang the unit on your
person.
When using the hook, check to make sure that the main unit
will not slip and fall, or become unstable by the wind, etc.
Never hang the unit from your belt or trousers as this could
cause accidents.
*4 Exchanging the rack (push-out rod)
NOTE
Install the rack (push-out rod) with its teeth facing
downward.
The rack (push-out rod) for 300 ml can also be used for
400 ml.
*5 Types of pistons
There are 3 types of pistons for diff erent sealing
materials.
a: Cartridges
b: Sausages
c: Buckets
Choose a holder and piston according to the sealing
material.
*6 Exchanging the piston
The piston can be detached from the rack (push-out rod)
by twisting the piston counter-clockwise. To attach it,
twist it in the opposite direction to screw it in. Exchanging
it does not require any tools.
*7 Using cartridges, sausages, and buckets
CAUTION
Do not make the diameter of the cut cross-section of the
nozzle 3 mm or smaller. Doing so may cause leakage
of sealing material on the piston side or damage to the
holder or holder cap.
*8 Temporarily setting down the tool while working
NOTE
The tool can be temporarily set down upside-down while
working. When doing so, set it down on a stable surface.
*9 Removing hardened sealing material
Use the pin included with the 300 ml holder to scrape out
and remove the hardened portion of the sealing material
inside the nozzle and cartridge, then return the pin to the
holder.
NOTE
Be careful not to scratch the inside of the container with
the pin.
13
English
21
6
22
6
―
228
Publicité
