Metabo SSEP 18 LTX BL MVT Notice Originale page 12

en ENGLISH
After completing the sawing cut, switch off the
machine and only take it out of the sawn gap to
place it down once the saw blade has come to
a standstill (danger of recoil).
Plunge cuts:
Plunge cuts may only be made in soft materials
such as wood or plastic. Only use short saw blades.
Hold the machine with both hands at the intended
handles, take a secure stance and concentrate on
the work.
See Fig. B, page 2: The machine is pressed with the
edge of the guide (2) against the workpiece. The
saw blade does not make contact with the
workpiece. Switch on the machine. The corner of
the guide serves as a pivot point around which the
machine is slowly aligned, whereby the saw blade
cuts into the workpiece.
9. Maintenance
On a regular basis, use compressed air to blow out
the machine through the rear ventilation slots.
Regularly clean the saw blade quick-clamping
device (3) and blow out with compressed air. Do not
oil or grease.
10. Accessories
Use only original Metabo or CAS (Cordless Alliance
System) battery packs and accessories.
See page 4.
Use only accessories which fulfil the requirements
and specifications listed in these operating instruc-
tions.
A Comprehensive range of saw blades for a wide
variety of materials and use cases
B Battery charger: ASC 145 (6.27378), ASC 55
(6.27044)
C Battery packs: 8,0 Ah (6.25369), 5,5 Ah
(625368), 5,2 Ah (6.25592)
D Lubricating stick for cooling the saw blades
when sawing metal
For a complete range of accessories, see
www.metabo.com or the catalogue.
11. Repairs
Repairs to electrical tools must be carried out
by qualified electricians ONLY!
If you have Metabo electrical tools that require
repairs, please contact your Metabo service centre.
For addresses see www.metabo.com.
You can download spare parts lists from
www.metabo.com.
12. Environmental Protection
Observe national regulations on environmentally
compatible disposal and on the recycling of disused
machines, packaging and accessories.
12
Battery packs must not be disposed of with regular
waste. Return faulty or used battery packs to your
Metabo dealer!
Do not allow battery packs to come into contact with
water!
Only for EU countries: Never dispose of
power tools in your household waste! In
accordance with European Guideline 2012/
19/EU on used electronic and electric equipment
and its implementation in national legal systems,
used power tools must be collected separately and
handed in for environmentally compatible recycling.
Before disposal, discharge the battery pack in the
power tool. Prevent the contacts from short-circu-
iting (e. g. by protecting them with adhesive tape).
13. Technical Specifications
Explanatory notes on the specifications on page 3.
Changes due to technological progress reserved.
U = Voltage of battery pack
n = Stroke rate at idle speed
0
s = Stroke length
T = max. cutting depth wood
1
T = max. cutting depth metal
2
( = profiles,
m = Weight (with smallest battery pack)
Measured values determined in conformity with
EN 62841.
Permitted ambient temperature during operation:
-20 °C (-4°F) to 50 °C (120°F) (limited performance
with temperatures below 0 °C (32°F)). Permitted
ambient temperature for storage: 0 °C (32°F) to
30 °C (86°F).
Direct current
The technical specifications quoted are subject to
tolerances (in compliance with the relevant valid
standards).
Emission values
Using these values, you can estimate the
emissions from this power tool and compare these
with the values emitted by other power tools. The
actual values may be higher or lower, depending on
the particular application and the condition of the
tool or power tool. In estimating the values, you
should also include work breaks and periods of low
use. Based on the estimated emission values,
specify protective measures for the user - for
example, any organisational steps that must be put
in place.
Vibration total value (vector sum of three directions)
determined in accordance with EN 62841:
a = vibration emission value (sawing of chip
h, B
boards)
a = vibration emission value (sawing of
h, WB
wooden planks)
K = Uncertainty (vibration)
h,...
During operation the noise level can exceed
80 dB(A).
Wear ear protectors!
= tubes)
