Bosch GDS 120-LI Professional Notice Originale page 14

14 | English
Cordless Impact Wrench
A)
Impact rate
– Setting 1
– Setting 2
A)
Max. torque , hard screwdriving application
according to ISO 5393
Machine screw diameter
Max. screw diameter
Tool holder
Weight according to EPTA-Procedure
01:2014
Recommended ambient temperature during
charging
Permitted ambient temperature during opera-
B)
tion and during storage
Recommended rechargeable batteries
Recommended chargers
A) measured at 20–25 °C with battery .
B) Limited performance at temperatures < 0 °C
Noise/vibration information
Noise emission values determined according to
EN 62841-2-2.
Typically, the A-weighted noise level of the power tool is:
Sound pressure level 92 dB(A); sound power level
103 dB(A). Uncertainty K = 3 dB.
Wear hearing protection!
Vibration total values a (triax vector sum) and uncertainty K
h
determined according to EN 62841-2-2:
Impact tightening of fasteners of the maximum capacity of
2
the tool: a = 9.5 m/s , K = 1.5 m/s
h
The vibration level and noise emission value given in these
instructions have been measured in accordance with a
standardised measuring procedure and may be used to com-
pare power tools. They may also be used for a preliminary
estimation of vibration and noise emissions.
The stated vibration level and noise emission value repres-
ent the main applications of the power tool. However, if the
power tool is used for other applications, with different ap-
plication tools or is poorly maintained, the vibration level
and noise emission value may differ. This may significantly
increase the vibration and noise emissions over the total
working period.
To estimate vibration and noise emissions accurately, the
times when the tool is switched off or when it is running but
not actually being used should also be taken into account.
This may significantly reduce vibration and noise emissions
over the total working period.
Implement additional safety measures to protect the oper-
ator from the effects of vibration, such as servicing the
power tool and application tools, keeping their hands warm,
and organising workflows correctly.
1 609 92A 7TL | (04.08.2022)
-1
min
-1
min
Nm
mm
mm
kg
°C
°C
Assembly
u
Battery Charging
u
Note: The battery is supplied partially charged. To ensure
full battery capacity, fully charge the battery in the charger
2
before using your power tool for the first time.
The lithium-ion battery can be charged at any time without
reducing its service life. Interrupting the charging process
does not damage the battery.
The lithium-ion battery is protected against deep discharge
by the "Electronic Cell Protection (ECP)". When the battery
is discharged, the power tool is switched off by means of a
protective circuit: The application tool no longer rotates.
u
Removing the battery (see figure A)
To remove the battery (6), press the release button (5) and
pull the battery downwards out of the power tool. Do not
use force to do this.
Changing the Tool
u
GDR 120-LI
0–1900
0–3200
100
M4–M12
8
¼" internal hexagon
1.1
0 to +35
–20 to +50
GBA 12V ...
GAL 12 ...
GAX 18 ...
Remove the battery from the power tool before carry-
ing out work on the power tool (e.g. maintenance,
changing tool, etc.). The battery should also be re-
moved for transport and storage. There is risk of injury
from unintentionally pressing the on/off switch.
Use only the chargers listed in the technical data. Only
these chargers are matched to the lithium-ion battery of
your power tool.
Do not continue to press the On/Off switch after the
power tool has automatically switched off. The battery
can be damaged.
Remove the battery from the power tool before carry-
ing out work on the power tool (e.g. maintenance,
changing tool, etc.). The battery should also be re-
GDS 120-LI
0–1900
0–3200
105
M4–M12
8
∎ 3/8"
1.1
0 to +35
–20 to +50
GBA 12V ...
GAL 12 ...
GAX 18 ...
Bosch Power Tools