Steinberg Systems SBS-FZ 1500/2M Manuel D'utilisation page 7

• REGULAR INSPECTIONS (recommended as monthly):
• Check chain wear and tear.
• Check the wear and tear of the hooks: level of wear and tear, damage, enlargement of the hook slit, shank bend
or hook deviation.
• Check fastening of the hooks.
• Clean and lubricate the chains.
POSSIBLE HAZARDS DURING USE
The hazards that can occur during use of the machine are mechanical hazards. The mechanical hazard occurs in situations in
which injuries can result from mechanical impact of various elements, e.g. machine parts, tools, etc. on people.
The basic mechanical hazards include squeezing, crushing, cutting, pulling in or catching; impact; puncture; abrasion; as well
as slipping and stumbling.
These hazards can occur both during normal machine operation and as a result of irregularities in machine operation. These
irregularities might result in machine failure.
The mechanical hazards can result from: moving machines, transported loads, moving elements, sharp/rough elements,
dropping elements/loads, slippery uneven surfaces, limited space, location of the work station in relation to the ground
(work at heights and in depths).
VII. CLEANING AND MAINTENANCE
The chain hoist must be cleaned regularly. After completion of work, remove all dirt from the chains and the machine itself.
The chains, hooks, hinges and hook latches must be regularly lubricated with grease. When the load chain is rusted, the
rust must be removed and the chain greased. If rust cannot be removed, the load chain must be replaced. All and any hoist
maintenance and inspection activities must be carried out by a trained and qualified employee. They cannot be conducted by
a person without proper experience and knowledge.
NOTE!
After 5 months of using the chain hoist (approximately if the hoist will be used more than 1500 times - 10 times daily), the
friction plates should be replaced.
Disassemble one by one the elements up to the element No. 22 (brake disc) inclusive - which should be replaced:
EN
22 21
23
26 24
31 27
32
34 33
35
36
25
28
29
39
30
40
38
37
18
20
19
46
47
48
49
50
51
52
46
12
Rev. 08.12.2020
VIII. GENERAL MACHINE DIAGRAM
16
15
18
17
20
19
22 21
23
26
24
31
27
32
33
34
35
36
46
47
48
25
49
28
50
51
29
52
39
30
40
38
37
46
1 Gear housing 25 Cover nut
2 Transmission 26 Gear selector rack
3 Shaft 27 Handle
4 Spline gearwheel 28 Gear selector ratchet
5 Transmission mounting plate 29 Spring nest
6 Mounting hook 30 Gear selector spring
7 Mounting hook protection 31 Sleeve
8 Shaft for the Upper Hook 32 Wheel
9 Disc 33 Washer
10 Guide 34 Screw
11 Stripper 35 Pin
12 Side plate 36 Nut
13 Bearing load ring 37 Name plate
14 Hub 38 Rivet
15 Spring 39 Washer
16 Spring ratchet 40 Screw
17 Ratchet 41 Load chain
18 Ring 42 Chain ring
Rev. 08.12.2020
3 2 1 24
4
5
7
9
6
8
10
14 12
41
42
11 60
13
44
61
10 45
62
53
69
63
43
54
55
64
56
65
57
58
59
47
60
49 Screw
50 Wheel
51 6t hook lower frame
52 Screw
53 Nut
54 Washer
55 6t arbor
56 Cover nut
57 Nut
58 Washer
59 Wheel arbor
60 9t hook x 2
61 Protection clip
62 9t hook upper frame
63 Screw
64 9t latch
65 9t hook lower frame
66 Nut
13
66
67
68
70
61
EN