Mitsubishi Electric CITY MULTI PLFY-WLMU-E Serie Manuel D'utilisation page 11

3. Operation
<Vane setting>
Fri
Swing Off Off
Vane Vent. Louver
F1 F2 F3 F4
ON
RETURN SELECT
MENU
OFF
HOLD
(Sample screen on CITY MULTI)
Fri
83
Room
Cool Set temp. Auto
83
Mode Temp. Fan
<Ventilation setting>
Fri
Low
Vent.
F1 F2 F3 F4
ON
RETURN SELECT
MENU
OFF
HOLD
<Returning to the Operation menu>
Operation
Vane·Louver·Vent. (Lossnay)
High power
Comfort
Main menu: RETURN
Cursor
F1 F2 F3 F4
ON
RETURN SELECT
MENU
OFF
HOLD
Notes:
●
During swing operation, the directional indication on the screen
does not change in sync with the directional vanes on the unit.
●
Available directions depend on the type of unit connected.
In the following cases, the actual air direction will diff er from the
●
direction indicated on the remote controller display.
1.While the display is in "STAND BY" or "DEFROST" states.
2. Immediately after starting heat mode (while the system is
waiting for the mode change to take eff ect).
3. In heat mode, when room temperature is higher than the temperature
setting.
Press the [F1] or [F2] button to go
through the vane setting options:
"Auto", "Step 1", "Step 2", "Step 3",
"Step 4", "Step 5" and "Swing".
Select the desired setting.
Auto
Auto Step 1 Step 2
Step 3 Step 4 Step 5
Swing
Swing
Select "Swing" to move the vanes
up and down automatically.
When set to "Step 1" through "Step
5", the vane will be fi xed at the se-
lected angle.
• under the vane setting icon
This icon will appear when the
vane is set to "Step 5" and the fan
operates at low speed during cool-
ing or drying operation (depends
on the model).
The icon will go off in an hour, and
the vane setting will automatically
change.
Press the [F3] button to go through
the ventilation setting options in the
order of "Off ", "Low", and "High".
* Settable only when Lossnay unit is
connected.
Off Low High
Off
Low
• The fan on some models of indoor
units may be interlocked with certain
models of ventilation units.
Press the [RETURN] button to go
back to the Operation menu.
< How to set the fi xed up/down air direction >
Notes:
●
This function cannot be set depending on the outdoor unit to be
connected.
• For PLFY-WL·NFMU-E series, only the particular outlet can be fi xed
to certain direction with the procedures below. Once fi xed, only the
set outlet is fi xed every time air conditioner is turned on. (Other outlets
follow UP/DOWN air direction setting of remote controller.)
■
Explanation of word
• "Refrigerant address No." and "Unit No." are the numbers given to
each air conditioner.
• "Outlet No." is the number given to each outlet of air conditioner.
(Refer to the illustration below.)
• "Up/Down air direction" is the direction (angle) to fi x.
Reset
horizontal
Horizontal airflow
Remote controller setting
The airflow direction of this
outlet is controlled by the airflow
direction setting of remote
controller.
Electric Component box
Outlet No.4
High
Outlet No.3
Note:
The outlet No. is indicated by the number of grooves on both
ends of each air outlet. Set the air direction while checking the
information shown on the remote controller display.
Air outlet identification marks
1 2 3 4
Downward
Fixed
The airflow direction of this outlet is fixed
in particular direction.
* When it is cold because of direct
airflow, the airflow direction can be
fixed horizontally to avoid direct airflow.
Outlet No.1
Outlet No.2
5
en
9