Whirlpool 400011209802/A Mode D'emploi page 17

Installation instructions for product with Hettich hinges
!
It is recommended that this installation be performed by authorized technical stuff.
!
Before installation, read the instructions carefully.
!
Fit the refrigerator/freezer in stable kitchen units only.
!
Cabinet dimensions are changed by material of trim flap
1. If material of trim flap
2. If material of trim flap
!
If necessary, reverse the door according to instructions.
1. See fig.A for the necessary attachment components.
2. Open the package. Take gasket spacer
Themiddle part is door hang rail
3. Insert trim flap into slot and screw by screws
(1)
4. Pass the power cord through ventilation shaft and position it so that the appliance could-
be easily plugged in once it has been installed. (fig.B - fig.C)
5. Cut trim gasket
(4)
ges of the appliance. (fig.E)
6. Raise the appliance and slide into the kitchen unit.
7. Lean the appliance to the kitchen unit through the hinges and align the front feet with
frontsurface of the kitchen unit. (fig.F)
8. Open the appliance door and screw the front feet by using screws
9. Screw trim flap
(1)
10. Screw the hinges to the kitchen unit using screws
11. Close the appliance door. Unscrew and remove the nuts
tbolts from the appliance door. (fig.H)
(12)
12. Remove the liner for the adhesive part on the door hang rails
rails
on theappliance door by inserting the bosses on the holes of the appliance door,
(10)
aligning thefront surfaces of the door hang rails(
each other. Letthe door hang rails
13. Slide the door hang
14. Take out the liners of the adhesive part on the front side of the door hang
15. Take out the liners of the adhesive part on the unit door spacers
onto theunit door(15), closer to the upper corners. (fig.K)
16. Lean the unit door
left,right and top edges with the sides of the unit or the doors of the nearer and upper
kitchenunits. (fig.K)
17. Make sure that the unit door
lowing the door hang
stays stuck on the unit door
18. Lay down the unit door
screws
. (fig.L)
(7)
19. To overcome some of the furniture mistakes, there are plastic spacers
door hang . Remove these plastic spacers
(2)
is plastic, look at (Table.1/B1) for cabinet dimensions.
(1)
is metal, look at (Table.1/B2) for cabinet dimensions.
(1)
. The other two parts are unit door spacers
(10)
to the height of the recess and stick it on reverse side of the doorhin-
to kitchen unit using screws
, stick onto the appliance door. (fig.H)
(10)
into door hang rails
(2)
to the door hang
(15)
sticks onto the door hang
(15)
to slide out the door hang rails
(2)
. (fig.L)
(15)
on the floor and screw the door hang
(15)
.
1
and brake into three as shown in figureD.
(9)
. (fig.E)
(8)
. (fig.G)
(7)
. (fig.G)
(7)
, washers
(14)
and the appliance door parallel to
10)
. (fig.J - fig.K)
(10)
, aligning the unit door spacers(11) on the
(2)
. Pull the unit door
(2)
. Observe that the door hang
(10)
. (fig.M)
(A)
17
. (fig.D)
(11)
. (fig.G)
(7)
and adjustmen-
(13)
. Place door hang
(10)
.
(2)
and and stick them
(11)
al-
(15)
to the unit door
(2) (15)
sticked on the
(A)
(2)
by