Berner BACAG-1 BL 18V Notice Originale page 27

The workpiece must be fixed if it is not heavy enough to be steady. Never
move the workpiece towards the rotating wheel by hand.
The flange nut must be securely tightened before the machine is started. If
the tool is not securely tightened with the flange nut, it is possible that the
tool will lose the required clamping force when it is decelerated.
OVERLOAD AND KICKBACK PROTECTION
The power tool has an overload and kickback safety function and stops if it
is overloaded. Switch off the power tool and then switch the power tool back
on again in order to continue to work.
SOFT START
Electronic soft start for save use prevents jerky run-up of the machine.
BRAKING SYSTEM
The run-on brake engages when the trigger is released, causing the tool to
stop within seconds.
Make sure that the insertion tool comes to a complete stop before laying
it down.
In comparison with tools without a run-on brake the run-on time will be
highly reduced by braking.
CLEANING
The ventilation slots of the machine must be kept clear at all times.
MAINTENANCE
Use only Berner accessories and Berner spare parts. Should components
need to be replaced which have not been described, please contact one of
our Berner service agents (see our list of guarantee/service addresses).
If needed, an exploded view of the tool can be ordered. Please state the
ten-digit No. as well as the machine type printed on the label and order the
drawing at Berner.
SYMBOLS
Please read the instructions carefully before starting
the machine.
CAUTION! WARNING! DANGER!
Remove the battery pack before starting any work on
the appliance.
Do not use the guard for cut-off operations.
Do not use force.
Use force.
Always wear eye protection!
Wear ear protectors.
Wear a suitable dust protection mask.
482 148 - Berner-BACAG-1 BL 18V.indd 27 482 148 - Berner-BACAG-1 BL 18V.indd 27
Wear gloves!
Always operate with two hands.
Only for grinding.
Only for cutting work.
Pay attention to permissible disc thickness.
Accessory - Not included in standard equipment,
available as an accessory.
Do not dispose of waste batteries, waste electrical and
electronic equipment as unsorted municipal waste.
Waste batteries and waste electrical and electronic
equipment must be collected separately.
Waste batteries, waste accumulators and light sources
have to be removed from equipment.
Check with your local authority or retailer for recycling
advice and collection point.
According to local regulations retailers may have an
obligation to take back waste batteries and Waste
electrical and electronic equipment free of charge.
Your contribution to re-use and recycling of waste
batteries and waste electrical and electronic equipment
helps to reduce the demand of raw materials.
Waste batteries, in particular containing lithium and
waste Electrical and electronic equipment contain
valuable, recyclable materials, which can adversely
impact the environment and the human health, if not
disposed of in an environmentally compatible manner.
Delete personal data from waste equipment, if any.
n
No-load speed
0
V
Voltage
Direct Current
European Conformity Mark
GUARANTEE AND GUARANTEE SERVICE
Each tool, spare part or accessory is consistently checked before being
dispatched from the manufacturing plant. If, despite this fact, there are any
defects, please send the item directly to our Client Services Headquarters
or to the nearest service repair shop of the firm Berner.
The warranty period of 36 months for tools and 12 months for batteries and
chargers starts on the date of purchase which must be verified using the
original receipt. During the guarantee period the producer guarantees:
• free removal of possible defects;
• free replacement of all damaged parts;
• free professional servicing.
The requirement for this is that the problem is a material and/or
manufacturing fault. Defects or faults caused by incorrect treatment or
excessive force are not covered by the warranty. Furthermore, only original
accessory parts may be used, which Berner has expressly identifi ed as
suitable for the operation with Berner machines.
You can find out the location of your nearest customer service workshop
under www.berner.eu.
27 ENGLISH
15.06.2023 10:17:41 15.06.2023 10:17:41