Publicité
Les langues disponibles
Les langues disponibles
90549168 SS12D, SS14, SS18 Smart Select
6. To reduce risk of damage to electric plug and cord, pull by plug rather than cord when
disconnecting charger.
7. Make sure cord is located so that it will not be stepped on, tripped over, or otherwise
subjected to damage or stress.
8. An extension cord should not be used unless absolutely necessary. Use of improper
extension cord could result in a risk of fire, electric shock or electrocution.
a. Two-wire cords can be used with 2-wire or 3-wire extension cords. Only round
jacketed extension cords should be used, and we recommend that they be listed by
Underwriters Laboratories (U.L.). If the extension is to be used outside, the cord must
be suitable for outdoor use. Any cord marked for outdoor use can also be used for
indoor work. The letters "W" or "WA" on the cord jacket indicate that the cord is
suitable for outdoor use.
b. An extension cord must have adequate wire size (AWG or American Wire Gauge) for
safety, and to prevent loss of power and overheating. The smaller the gauge number
of the wire, the greater the capacity of the cable; that is, 16 gauge has more capacity
than 18 gauge. When using more than one extension to make up the total length, be
sure each extension contains at least the minimum wire size.
CHART FOR MINIMUM WIRE SIZE (AWG)OF EXTENSION CORDS
Total Extension Cord Length (ft)
Wire Gauge
9. Use only the supplied charger when charging your drill. The use of any other charger
could damage the drill or create a hazardous condition.
10. Use only one charger when charging.
11. Do not attempt to open the charger or the drill. There are no customer serviceable
parts inside. Return to any authorized Black & Decker service center.
12. DO NOT incinerate the drill or battery packs even if they are severely damaged or
completely worn out. The batteries can explode in a fire.
13. A small leakage of liquid from the battery pack cells may occur under extreme usage,
charging or temperature conditions. This does not indicate a failure. However, if the
outer seal is broken and this leakage gets on your skin:
a. Wash quickly with soap and water.
b. Neutralize with a mild acid such as lemon juice or vinegar.
c. If the battery pack liquid gets in your eyes, flush them with clean water for a minimum
of 10 minutes and seek immediate medical attention. MEDICAL NOTE: The liquid is
a 25-35% solution of potassium hydroxide.
CHARGING THE POWER PACK
Your drill may use either a jack plug charger or a cup charger, both of which are described
below. Please follow the directions for the type of charger that you have. Chargers are
designed to use standard 120 volt AC, 60 Hz power. Do not use DC or any other voltage.
THE BATTERIES IN YOUR POWER PACK ARE NOT FULLY CHARGED AT THE
FACTORY. BEFORE ATTEMPTING TO CHARGE THEM, THOROUGHLY READ ALL OF
THE SAFETY INSTRUCTIONS.
INSTRUCTIONS FOR JACK PLUG CHARGERS:
1. Place the battery pack into the tool until it
"clicks" into place.
2. Insert the charger plug into the connector as
shown in figure B.
3. Plug the charger (6) into any standard 120
Volt 60 Hz electrical outlet and let the battery
pack charge initially for 12 hours. After the
initial charge, under normal usage, your
power pack should be fully charged in 6 to 12
hours.
4.
WARNING: Fire Hazard. Disconnect the
charger from the outlet first, then disconnect
the charger from the tool. Do not use the tool
while it is connected to the charger.
6/2/09
NAMEPLATE RATING AMPS – 0 – 10.0
0-25
26-50
(0-7,6m) (7,6-15,2m) (15,2-30,4m) (30,4-45,7m)
18
16
6
10:07 AM
Page 6
51-100
101-150
16
14
B
6
Publicité
