Publicité
Les langues disponibles
Les langues disponibles
OUTSIDE BACK EXHAUST
B
INSTALLATION OVERVIEW
B1. Prepare Rear Wall
B2. Remove Blower Plate
B3. Attach Mounting Plate to Wall
B4. Prepare Top Cabinet
B5. Adjust Blower
B6. Mount the Microwave Oven
IMPORTANT NOTES:
•
Make sure the screws for the
blower motor and blower plate
are securely tightened when
they are reinstalled. This will
help to prevent excessive
vibration.
•
Make sure the motor wiring has
been properly routed and secured,
and that the wires are not pinched.
PREPARING THE REAR WALL
B1.
FOR OUTSIDE BACK EXHAUST
You need to cut an opening in the rear wall for
outside exhaust.
NOT E:
REA D
IT IS VER
AND FOLL
Y IMPO
RTAN
IN THE
OW THE
T TO
BEFO
INST ALLA
DIRE CTIO
RE PRO
TION INST
NS
REA R
CEE DING
RUC TION
WAL L
TEM PLAT
WITH
S
This Rear
E.
THIS
3/8" TO EDGE
mounti
ng plate
Wall Templa
outlet.
and to
te serves
to positio
12"
1. Use
locate the
n the bottom
a level
to check
horizon
tal exhaus
accura
tely.
that the
t
2. Locate
and mark
templa
te is positio
right side
at least
ned
of the centerl
one stud
4"
I t is importa
ine.
on the
left or
screw mounte
nt to use
of the microw
d firmly
in a stud
at least
one wood
locatio ns
ave. Mark
to suppor
3. Drill
for the
supplie
two additio
t the weight
holes in
the marked
d toggle
nal, evenly
spaced
a stud,
drill a 3/16"
locatio ns.
bolts.
that do
not line
hole for
Where
toggle
up with
wood screws
there is
bolts.
a stud,
drill 5/8"
. For holes
AT THIS
D O NOT
holes for
TIME.
INSTA LL
THE MOUN
4. Remov
e the templa
TING PLATE
5. Review
te from
installa
the Installa
the rear
tion situatio
tion Instruc
tion book
wall.
n.
for your
Darle vuelta
a la hoja
versió n
en Españ
para consu
ol.
ltar la
Loca te
and mark
moun ting
holes to
plate .
align with
IMPO RTAN
holes in
T:
the
LOC ATE
THE CEN
AT LEAS
T ONE
MAR K
TERL INE.
STUD
ON EITH
THE LOC
ER SIDE
SPAC
ATIO N
OF
ED TOG
FOR 2
ARE A.
GLE BOLT
ADD ITION
S IN THE
AL, EVEN
MOU NTIN
LY
G PLAT
E
Trim the
rear wall
temp late
alon g
the dotte
d line.
Loca te
and mark
moun ting
plate .
IMPO RTAN
T:
LOC ATE
AT LEAS
THE CEN
TERL INE.
MAR K
THE LOC
SPAC
ED TOG
ARE A.
•
Read the instructions on the REAR
WALL TEMPLATE.
•
Tape it to the rear wall.
•
Cut the opening, following the instructions of the
REAR WALL TEMPLATE.
Installation Instructions
NOTE: IT IS VERY IMPORTANT
READ AND FOLLOW
IN THE INSTALLATIO
BEFORE PROCEEDING
REAR WALL TEMPLATE.
This Rear Wall Template
mounting plate and to locate
outlet.
1. Use a level to check that
accurately.
2. Locate and mark at least
right side of the centerline.
screw mounted firmly in
of the microwave. Mark
locations for the supplied
3. Drill holes in the marked
a stud, drill a 3/16" hole
that do not line up with
toggle bolts.
AT THIS TIME.
4. Remove the template
5. Revie
installation situation.
Darle vuelta a la hoja
versión en Español.
Locate and mark holes
mounting plate.
IMPORTANT:
LOCATE AT LEAST ONE
THE CENTERLINE.
MARK THE LOCATION
SPACED TOGGLE BOLTS
AREA.
Trim the rear wall template
Trim the
rear wall
temp late
alon g
the dotte
d line.
holes to
align with
holes in
the
T ONE
STUD
ON EITH
ATIO N
ER SIDE
FOR 2
OF
GLE BOLT
ADD ITION
S IN THE
AL, EVEN
MOU NTIN
LY
G PLAT
E
(Horizontal Duct)
3/8" TO EDGE
along the dotted line.
Trim the rear wall template
12"
TO
THE DIRECTIONS
N INSTRUCTION S
WITH THIS
4"
serves to position the bottom
the horizontal exhaust
the template is positioned
one stud on the left or
least one wood
It is important to use at
a stud to support the weight
two additional, evenly spaced
toggle bolts.
locations. Where there is
for wood screws. For holes
a stud, drill 5/8" holes for
DO NOT INSTALL THE
MOUNTING PLATE
from the rear wall.
book for your
w
h t
e Installation Instruction
para consultar la
to align with holes in the
STUD ON EITHER SIDE
OF
FOR 2 ADDITIONAL,
EVENLY
IN THE MOUNTING PLATE
to align with holes in the
Locate and mark holes
. e
m
o
u
t n
n i
g
l p
t a
IMPORTANT:
STUD ON EITHER SIDE
OF
LOCATE AT LEAST ONE
THE CENTERLINE.
EVENLY
FOR 2 ADDITIONAL,
MARK THE LOCATION
IN THE MOUNTING PLATE
along the dotted line.
SPACED TOGGLE BOLTS
AREA.
B2.
Remove and save the screw that holds the blower
plate to the microwave. Lift off the blower plate.
Blower Plate
EN-16
REMOVE BLOWER PLATE
Back of
Microwave
Publicité
