Rowenta SILENCE FORCE EXTREME RO82 Serie Mode D'emploi page 14

EN
USE
1 • Fitting the elements onto the
appliance
Clip the end of the hose to the suction inlet located at the
front of the appliance (fig.1). To remove, unclip the end
using the clip and remove.
Fix the accessory support to the notch in the parking
position located at the back of the vaccuum cleaner (fig.2)
and store the accessories on top.
Note: The accessory support does not need to be removed
to open the vacuum cleaner lid.
• Fit the metal telescopic tube to the end of the nozzle until
you hear a click indicating that it is locked (fig.3). To remove,
press the tube lock button and remove.
• Fit the multi-surface nozzle (23) to the end of the metal
telescopic tube until you hear a click indicating that it is
locked (fig.4). To remove, press the nozzle lock button and
remove.
• Adjust the metal telescopic tube to the desired length
using the telescopic system (TELESCOPIC SYSTEM) (fig.5).
Fit the corresponding accessory to the end of the metal
telescopic tube or the nozzle:
- For rugs and carpets: use the multi-surface nozzle in the
retracted brush nozzle position or the Turbo-brush* (fibres
and animal hairs).
- For smooth surfaces and smooth surfaces with crevices
(such as tiled floors): use the all-surface nozzle (23) with
the brush extended or, for better results, use the smooth
surface nozzle* (28.a*) without the removable brush.
- For fragile surfaces, such as parquet, it is recommended
to use the standard parquet nozzle (27*) or the nozzle
with a line of bristles (28.b*)
IMPORTANT: The nozzle for smooth surface with
crevices 28.a* is used to measure performance
associated to the energy label. This nozzle allows
you to optimise the dust-collection performance of
your appliance on smooth surfaces with crevices.
- For corners and hard to reach spots: use the telescopic
crevice nozzle*.
- For upholstery and delicate surfaces: use the brush with
the nozzle (EASY BRUSH) or the upholstery nozzle*.
ATTENTION: do not operate your vacuum cleaner
without the filtration system fitted (foam, microfilter and
filter).
IMPORTANT: always switch off and disconnect your
vacuum cleaner before changing the accessories.
* According to model: these systems are specific to certain mo-
dels or are accessories available as an option.
ERGONOMIC RECOMMENDATIONS
ERGO COMFORT SILENCE range
Ergonomic, the ERGO COMFORT SILENCE range
has been designed to facilitate and improve user
comfort when vacuuming.
To prevent bending over and to ensure upright
posture, make sure to:
1. Adjust the length of the ERGO COMFORT
SILENCE metal telescopic tube to your body (fig.6).
2. Place your second hand on the front of the ERGO
COMFORT SILENCE nozzle handle (fig.7).
2 • Plugging in the power cord and
switching on the appliance
Unwind the power cord completely, plug in your vacuum
cleaner and press the ON/OFF button (fig. 8).
Set the suction power using the manual power switch* on
the power nozzle (fig.9):
• Position (MIN) for vacuuming delicate fabrics
(curtains, textiles).
• Position (Medium) for daily vacuuming of all types
of surfaces with low levels of soiling.
• Position (MAX) for vacuuming hard floors (tiled
floors, parquet, etc.) and rugs and
carpets in the case of high levels of soiling.
3 • Storing and transporting the
appliance
After use, switch off your vacuum cleaner by pressing the
ON/OFF button and unplug it (fig. 10). Wind the power cord
by pressing the power cord wind button (fig. 11).
It is easy to carry your vacuum cleaner using the handle (8).
Do not carry your appliance using the dust compartment
handle (fig.12).
When storing your vacuum cleaner, place the tube in its
storage compartment at the back of the appliance (fig.13).
You do not need to remove the accessory support* to store
the accessory range (Fig.14).
10