Ryobi LLCDI1802 Manuel D'utilisation page 8

GB
FR DE ES IT
OPERATION
NOTE: The drill will not run unless the rotation selector is
pushed fully to the left or right.
Avoid running the drill at low speeds for extended periods
of time. Running at low speeds under constant usage
may cause the dr ill to become o verheated. If this occurs ,
cool the drill by running it without a load and at full speed.
INTERNAL SPINDLE LOCK
The inter nal spindle loc k allo ws the user single-handed
control of chuck adjustments and bit changes . Squeezing
the chuc k body stops the chuc k ja ws from tur ning. F or
bit changes and chuc k adjustments , squeez e the chuc k
body and turn.
KEYLESS CHUCK
See Figure 4.
The dr ill has a k eyless chuc k to tighten or release dr ill
bits in the chuc k jaws. The arrows on the chuc k indicate
which direction to rotate the chuck body in order to LOCK
(tighten) or UNLOCK (release) the drill bit.
WARNING
Do not hold the chuck with one hand and use the
power of the drill to tighten the chuck jaws on the
drill bit. The chuck body could slip in y our hand,
or your hand could slip and come in contact with
the rotating drill bit. This could cause an accident
resulting in serious personal injury.
TWO-SPEED GEAR TRAIN (HI-LO)
See Figure 5.
The dr ill has a tw o-speed gear tr ain designed f or dr illing
or dr iving at LO (1) or HI (2) speeds . A slide s witch is
1. APPLICATION
• Lag screws up to 9.5 mm dia. by 38.1 mm long
• Hole saw up to 50.8 mm
• Spade bits up to 38.1 mm
• Drill bits up to 12.7 mm
• Drilling into metal
• Concrete screws
• Drill bits up to 6.4 mm
• Deck or wood screws up to 76.2 mm long
• Self tapping screws
• Deck or wood screws up to 76.2 mm long
• Small screws or delicate work that requires more control
• Masonry bit up to 12.7 mm
NL PT DK SE FI NO
English
RU PL CZ HU RO LV
located on top of the dr ill to select either LO (1) or HI (2)
speed. When using drill in the LO (1) speed range, speed
will decrease and unit will ha ve more po wer and torque .
When using dr ill in the HI (2) speed r ange, speed will
increase and unit will ha ve less po wer and torque . Use
LO (1) speed for high power and torque applications and
HI (2) speed for fast drilling or driving applications.
NOTE: If y ou ha ve difficulty changing from one gear
range to the other, turn the chuck by hand until the gears
engage.
CAUTION:
Never change gears while the tool is r unning.
Failure to obey this caution could result in serious
damage to the drill.
QUICK MODE SELECTOR
See Figure 6.
The Quic k Mode Selector allo ws y ou to quic kly s witch
from drill mode to drive mode.
In gener al, dr ill mode should be used f or dr illing and
other hea vy duty applications . Dr ive mode should be
used for driving screws . Hammer
for impact drilling.
SELECTING DRIVE OR DRILL SETTING
See Figure 5-6.
Using the char t belo w, choose correct speed and mode
the type of bit, fastener, and material you will be using.
Choose your APPLICATION
■
Choose the correct SPEED: (1/LOW or 2/HIGH)
■
Choose the correct MODE: (DRIVE, DRILL, OR
■
HAMMER)
2. SPEED
1/LOW
(TORQUE ADJUSMENT NOT ACTIVE)
2/HIGH
1/LOW
2/HIGH
1/LOW
(TORQUE ADJUSMENT NOT ACTIVE)
2/HIGH
3
LT EE HR SI SK GR
mode should be used
3. MODE
DRILL MODE
DRIVE MODE
HAMMER MODE
TR