Kärcher RCF 3 Mode D'emploi page 21

The cleaning robot gives a verbal signal and first
creates a map of the surroundings without cleaning.
The LED display indicator "Robot status" lights up
blue.
When the map creation is finished, it returns to the
charging station.
As soon as the cleaning robot is connected to the
charging station, the LED display indicator "Robot
status" lights up yellow and the LED display indica-
tor "Battery" pulses green.
Note
Wait a few seconds until you press the On/Off/Pause
button again so that the robot can save the map.
2. Press the On/Off/Pause button.
The cleaning robot gives a verbal signal and starts
cleaning.
The LED display indicator "Robot status" lights up
blue.
Operation with the app
Creating a map
Note
Open the doors to all rooms that the cleaning robot is to
clean and keep the floor free of objects lying around.
1. In the app, press the control panel "Start" and follow
the steps indicated as needed.
The cleaning robot gives a verbal signal and starts
the map creation.
The LED display indicator "Robot status" lights up
blue.
When the map creation is finished, it returns to the
charging station.
As soon as the cleaning robot is connected to the
charging station, the LED display indicator "Robot
status" lights up yellow and the LED display indica-
tor "Battery" pulses green.
Note
When the cleaning robot is connected to the charging
station, it takes a few seconds to create the map in the
app. The LED display indicator "Robot status" pulses
yellow.
After the map has been successfully saved, an acoustic
signal sounds.
Configuring the robot in the app
Individual configurations of the map can be made in the
app.
● Virtual walls and restricted areas prevent the clean-
ing robot from entering areas that should not be
cleaned.
● With spot cleaning or cleaning zones, the robot can
specifically clean the areas selected by the user
once.
● With different cleaning modes, the cleaning intensity
can be selected individually for each room depend-
ing on the type of floor or soiling (amount of water,
number of passes per area, different roller speeds
and robot travel speed, etc.)
Downloading the app is described in the chapter Con-
necting cleaning robots with WLAN and App.
1. Follow the step-by-step instructions in the App.
Starting cleaning
1. Select the desired map in the app and start cleaning
according to the individual configuration.
Interrupting cleaning
Interrupt cleaning on the device:
1 Press any button during cleaning.
The cleaning robot stops.
The LED display indicator "Robot status" pulses
blue.
2 Press the On/Off/Pause button.
Cleaning continues.
Interrupt cleaning in the app:
1. In the app, press the control panel "Start".
The cleaning robot stops.
The LED display indicator "Robot status" pulses
blue.
2. In the app, press the control panel "Start".
Cleaning continues.
Battery level indicator
The LED display indicator "Battery" shows the battery
status, see chapter LED symbols on the display.
Optical signals warn of a flat battery.
● The LED display indicator "Robot status" flashes red
when the battery is empty and needs to be re-
charged.
● When charging in the charging station, the LED dis-
play indicator "Robot status" flashes red if the bat-
tery level is still too low to continue cleaning.
Note
If the cleaning robot has not finished cleaning, it will in-
dependently return to the place where cleaning was in-
terrupted after charging the battery.
Manually sending the cleaning robot for
Procedure on the device:
1 If the robot is currently performing a cleaning run,
press any button.
The cleaning robot stops.
The LED display indicator "Robot status" pulses
blue.
2 Press the Home button.
The cleaning is cancelled.
The cleaning robot moves to the charging station for
recharging. The cleaning robot emits a verbal sig-
nal.
As soon as the cleaning robot is connected to the
charging station, the LED display indicator "Robot
status" lights up yellow and the LED display indica-
tor "Battery" pulses green.
Procedure in the app:
1. If the robot is currently performing a cleaning run,
press the control panel "Start" in the app.
The cleaning robot stops.
The LED display indicator "Robot status" pulses
blue.
2. In the app, press the control panel "Charge".
The cleaning is cancelled.
The cleaning robot moves to the charging station for
recharging. The cleaning robot emits a verbal sig-
nal.
As soon as the cleaning robot is connected to the
charging station, the LED display indicator "Robot
status" lights up yellow and the LED display indica-
tor "Battery" pulses green.
The cleaning robot automatically returns to the charging
station for recharging when it has completed a cleaning
task or when it is low on energy during a cleaning pro-
cess.
English
recharging
21