Publicité
Les langues disponibles
Les langues disponibles
NOTE: Pass the dolly strap under the handles.
NOTE: Pass the dolly strap under the handles.
1.
1.
Place pieces of the shipping carton on the floor when
Place pieces of the shipping carton on the floor when
rolling the dolly and refrigerator into the house. Move
rolling the dolly and refrigerator into the house. Move
the refrigerator close to the built-in opening.
the refrigerator close to the built-in opening.
2.
2.
Place top of cardboard carton or plywood under
Place top of cardboard carton or plywood under
refrigerator.
refrigerator.
3.
3.
Stand the refrigerator up. First, place the left bottom
Stand the refrigerator up. First, place the left bottom
edge of the refrigerator on the floor, stand the
edge of the refrigerator on the floor, stand the
refrigerator upright and then lower the right-hand
refrigerator upright and then lower the right-hand
side of the refrigerator to the floor.
side of the refrigerator to the floor.
4.
4.
Reassemble the trim and top grille after the dolly has
Reassemble the trim and top grille after the dolly has
been removed from the refrigerator.
been removed from the refrigerator.
INSTALL ANTI-TIP BOARDS
INSTALL ANTI-TIP BOARDS
IMPORTANT:
IMPORTANT:
To avoid tipping during use, the solid soffit must be
To avoid tipping during use, the solid soffit must be
within 1" (2.5 cm) maximum above the refrigerator. If
within 1" (2.5 cm) maximum above the refrigerator. If
the solid soffit is higher than 1" (2.5 cm) or one is not
the solid soffit is higher than 1" (2.5 cm) or one is not
available, then the refrigerator must be braced.
available, then the refrigerator must be braced.
It is recommended that board(s) be installed before
It is recommended that board(s) be installed before
the refrigerator is installed.
the refrigerator is installed.
Board(s) must be long enough to fully cover the
Board(s) must be long enough to fully cover the
width of the compressor cover.
width of the compressor cover.
Locate the board(s) so the bottom surface(s) of the
Locate the board(s) so the bottom surface(s) of the
board(s) is (are) 84" (213 cm) from the floor.
board(s) is (are) 84" (213 cm) from the floor.
During installation, raise the refrigerator up so there
During installation, raise the refrigerator up so there
is 1/4" (6.35 mm) maximum between the top of the
is 1/4" (6.35 mm) maximum between the top of the
refrigerator and the bottom of the anti-tip board(s).
refrigerator and the bottom of the anti-tip board(s).
Do not crush the compressor cover when raising the
Do not crush the compressor cover when raising the
rear leveling legs.
rear leveling legs.
NOTE: The foam gasket, on top of the compressor
NOTE: The foam gasket, on top of the compressor
cover, will compress to fit under the anti-tip board(s).
cover, will compress to fit under the anti-tip board(s).
There is no need to trim the gasket.
There is no need to trim the gasket.
TO INSTALL ANTI-TIP BOARDS
TO INSTALL ANTI-TIP BOARDS
1.
1.
Mark the stud locations on rear wall.
Mark the stud locations on rear wall.
2.
2.
Securely attach two 2" x 4" x 32" (5 cm x 10 cm x 81 cm)
Securely attach two 2" x 4" x 32" (5 cm x 10 cm x 81 cm)
boards to wall studs behind refrigerator. Use six
boards to wall studs behind refrigerator. Use six
#8 x 3" (7.6 cm) (or longer) wood screws. The wood
#8 x 3" (7.6 cm) (or longer) wood screws. The wood
screws must be screwed into the studs at least
screws must be screwed into the studs at least
1½" (3.8 cm). The boards must overlap the compressor
1½" (3.8 cm). The boards must overlap the compressor
cover.
cover.
2" (5 cm)
2" (5 cm)
2" (5 cm)
D
D
A. Center board 1/4" (6.35 mm)
A. Center board 1/4" (6.35 mm)
max. above refrigerator
max. above refrigerator
B. Two 2" x 4" x 32" (5 cm x
B. Two 2" x 4" x 32" (5 cm x
10 cm x 81 cm) boards
10 cm x 81 cm) boards
CONNECT THE WATER SUPPLY
CONNECT THE WATER SUPPLY
Read all directions before you begin.
Read all directions before you begin.
IMPORTANT:
IMPORTANT:
If you turn the refrigerator on before the water line is
If you turn the refrigerator on before the water line is
connected, turn the ice maker OFF.
connected, turn the ice maker OFF.
Connect to potable water supply only.
Connect to potable water supply only.
Do not use with water that is microbiologically unsafe or
Do not use with water that is microbiologically unsafe or
of unknown quality without adequate disinfection before
of unknown quality without adequate disinfection before
or after the system. Systems certified for cyst reduction
or after the system. Systems certified for cyst reduction
may be used on disinfected waters that may contain
may be used on disinfected waters that may contain
filterable cysts.
filterable cysts.
CONNECT TO WATER LINE
CONNECT TO WATER LINE
PARTS NEEDED
PARTS NEEDED
Minimum 7 ft (2.13 m) flexible, codes-approved water
Minimum 7 ft (2.13 m) flexible, codes-approved water
supply line
supply line
STYLE 1—SHUTOFF VALVE CONNECTION
STYLE 1—SHUTOFF VALVE CONNECTION
NOTE: If your water line connection does not look like
NOTE: If your water line connection does not look like
Style 1, see "Style 2—Copper Line Connection."
Style 1, see "Style 2—Copper Line Connection."
1.
1.
Unplug refrigerator or disconnect power supply.
Unplug refrigerator or disconnect power supply.
IMPORTANT:
IMPORTANT:
There is not enough clearance to achieve a flush
There is not enough clearance to achieve a flush
installation if a water shutoff valve is located in the
installation if a water shutoff valve is located in the
wall behind the refrigerator. The water shutoff should
wall behind the refrigerator. The water shutoff should
be located in the base cabinet on either side of the
be located in the base cabinet on either side of the
refrigerator.
refrigerator.
A
A
B
B
C
C
C. Attach to studs with six
C. Attach to studs with six
#8 x 3" (7.6 cm) screws
#8 x 3" (7.6 cm) screws
D. Compressor cover
D. Compressor cover
11
Publicité
