Porter Cable PCXH80KT Instructions D'utilisation Et Manuel Du Propriétaire page 6

NEVER LEAVE THE HEATER UNATTENDED WHILE BURNING! NEVER LEAVE THE HEATER UNATTENDED WHILE BURNING! NEVER LEAVE THE HEATER UNATTENDED WHILE BURNING!
TROUBLE SHOOTING
SYMPTOM
High­limit­switch­Open­Circuit­
Sparks,­calling­for­flame,­but­
no­or­slow­motor­operation­
­ ­
­ ­
­ ­
­ ­
­ ­
­ ­
­ ­
No­Spark­ ­
­ ­
­ ­
­ ­
­ ­
Abnormal­Motor­Operation­-­
Motor­overheats­or­Stops­
­ ­
­ ­
­ ­
­ ­
Unable­to­Detect­Flame­
­ ­
­ ­
­ ­
­ ­
­ ­
­ ­
­ ­
­ ­
Flame­Control­Failure­
­ ­
TROUBLE SHOOTING
1)­ Make­sure­heater­is­cooled­off,­toggle­switch­to­"OFF"­position,­wait­5­minutes­and­retry.
1)­ Check­wiring­to­motor­(per­wiring­schematic­in­manual).
2)­ Make­sure­that­the­pressure­gauge­is­in­place­and­not­damaged.
3)­ Adjust­pressure­for­proper­heater­operation­per­manual.
4)­ With­heater­disconnected­from­AC­source,­rotate­fan­clockwise­to­verify­motor­is­free.
5)­ Remove­air­filter­housing­from­motor­and­inspect­the­pump­rotor­for­damage.­If­damaged,­replace­rotor­assembly.
6)­ If­wiring­is­correct,­pump­rotor­is­okay,­and­motor­is­not­rotating­freely,­replace­motor­or­power-pack­assembly.
7)­ If­problem­persists,­replace­oil­flame­control­assembly.
8)­ Check­for­spark­arching­from­the­electrode­assembly,­to­the­combustion­cylinder.
9)­­ Check­the­cad­cell­for­continuity.
1)­­ Check­length­and­gage­of­extension­cord­for­proper­amp.­draw.­(Check­requirements­on­page­4.)
2)­ Check­wiring­to­igniter­(per­wiring­schematic­in­manual).
3)­ Check­gap­between­electrode­probes­(2.3­-­3­mm).
4)­ Still­no­spark,­replace­igniter­assembly.
5)­ Replace­oil­flame­control­assembly.
1)­ Motor­speed­too­low­(Motor­should­operate­at­3450rpm)­-­Replace­motor.­
2)­ With­heater­disconnected­from­AC­source,­rotate­fan­clockwise­to­verify­motor­is­free.
3)­ Remove­air­filter­housing­from­motor­and­inspect­the­pump­rotor­for­damage.­If­damaged,­replace­rotor­­
­ assembly.
4)­ If­wiring­is­correct,­pump­rotor­is­okay,­and­motor­is­not­rotating­freely,­replace­motor­or­power-pack­assembly.
5)­ Replace­oil­flame­control­assembly.
1)­ Check­wiring­to­cad­cell­(per­wiring­schematic­in­manual).
2)­ Clean­cad­cell­photo­cell.
­ a)­­ Slide­cad­cell­out­of­cad­cell­holder.
­ b)­­ Push­the­photo­cell­out­of­the­black­rubber­cad­cell­housing­by­pushing­on­the­2­purple­wires.
­ c)­­ Clean­the­photo­cell­with­a­soft­cloth­and­rubbing­alcohol.
­ d)­­ Pull­the­photo­cell­back­into­the­cad­cell­housing­and­reinstall­into­holder.
­ e)­­ Test­heater.
3)­ If­the­heater­still­does­not­operate,­replace­cad­cell.
4)­ Replace­oil­flame­control­assembly.
1)­ Check­wiring­in­heater­(per­wiring­schematic­in­manual).
2)­ Replace­oil­flame­control­assembly.
Porter Cable | Kerosene Forced Air Heater
6
Operating Instructions and Owner's Manual