Porter Cable PCXH80KT Instructions D'utilisation Et Manuel Du Propriétaire page 4

NEVER LEAVE THE HEATER UNATTENDED WHILE BURNING! NEVER LEAVE THE HEATER UNATTENDED WHILE BURNING! NEVER LEAVE THE HEATER UNATTENDED WHILE BURNING!
OPERATING INSTRUCTIONS
UNPACKING
1.­ Remove­heater­from­carton.
2.­ Remove­all­protective­material­which­may­have­been­applied­
to­the­heater­for­shipment.
3.­ Check­the­heater­for­possible­shipping­damage.­If­any­
damage­is­found­immediately­contact­the­manufacturer­at­
888-848-5175.
ASSEMBLY (For­140,000­and­210,000­BTU/hr­models­only)
Wheels,­axle,­and­handles­are­found­in­the­shipping­carton­along­
with­mounting­hardware.
1.­ Handles­come­pre-assembled­on­the­tank.­The­transport­
handle­and­support­foot­simply­snap­into­place.
2.­ To­assemble­the­wheels,­first­Install­one­of­the­large­lock­nut­
onto­the­end­of­the­axle.
3.­ Slide­one­wheel­onto­the­axle­next­to­the­nut,­then­one­
spacer.
4.­ Slide­the­partially­assembled­axle­through­the­wheel­support­
frame.
5.­ Slide­the­spacer­onto­the­axle­next­to­the­wheel­support.
6.­ Slide­the­wheel,­then­large­last­large­lock­nut­onto­the­axle.­
Using­two­adjustable­wrenches­hold­both­nuts­and­tighten.­
DO­NOT­OVERTIGHTEN.
PREPARING FOR OPERATION
1.­ Check­the­heater­for­possible­shipping­damage.­If­any­is­
found,­immediately­contact­the­manufacturer­at­
888-848-5175.
2.­ Follow­all­of­the­"Precautions".­
3.­ Fill­the­fuel­tank­with­clean­kerosene.­In­extremely­cold­
weather,­condensation­may­develop­in­the­tank­and­it­is­
recommended­that­a­tablespoon­of­de-icer­be­added­for­
each­gallon­(3.78­Liters)­of­fuel­in­the­tank.­When­filling­
the­heater,­use­at­least­2­gallons­(7.57­liters)­of­fuel.­Be­sure­
heater­is­level­and­do­not­overfill.­Use­a­funnel­or­can­with­a­
long­fill­spout.
IMPORTANT: Before filling fuel tank the first time or after ex-
tended storage periods, drain the fuel tank of any moisture
or condensation.
4.­ Locate­heater­at­a­safe­distance­from­combustible­materials.­
Model­PCXH80KT­is­not­suitable­for­use­on­wood­floors­or­
other­combustible­materials.­When­used,­the­heater­should­
rest­on­suitable­insulating­material­at­least­1­inch­thick­and­
extending­3­ft.­or­more­beyond­the­heater­in­all­directions.
HEATER START UP
1.­ Turn­thermostat­to­lowest­setting,­and­make­sure­"On/Off"­
switch­is­"Off".­Plug­the­heater­into­a­grounded­115V,­60­Hz,­
1­Ø­outlet.­Turn­thermostat­to­highest­setting.­Start­heater­
by­pushing­toggle­switch­to­"On"­position­(light­signifies­
switch­is­in­"ON"­position).­Adjust­thermostat­to­desired­
setting.­Heater­will­cycle­on/off­as­heat­is­required.
EXTENSION­CORD­REQUIREMENTS:­Up­to­100'­(30.5m)­use­
16­awg.­conductor.­101'­-­200'­(30.5­-­61.0m)­use­14­awg.­
conductor.
Porter Cable | Kerosene Forced Air Heater
Notes:
•­ In­cold­weather­(below­10°­F),­starting­may­be­improved­by­
holding­a­finger­over­the­vent­hole­of­the­pump­adjustment­
screw­cap­until­the­heater­starts.­
•­ This­unit­is­equipped­with­an­interrupt­circuit.­The­reset­is­
integrated­into­the­"On/Off"­switch.­If­the­unit­does­not­
start,­toggle­the­switch­to­"Off",­wait­5­min.­and­toggle­
the­switch­to­"On".
HEATER SHUT DOWN
1.­ Push­"On/Off"­switch­to­"Off"­position.­For­extended­
shutdown,­unplug­heater­from­power­source.
RESTART AFTER SAFETY SHUTDOWN
1.­ Toggle­switch­to­"OFF"­position,­wait­5­minutes.­Restart.
MAINTENANCE AND STORAGE
WARNING.­To­prevent­personal­injury,­unplug­the­heater­from­
the­wall­outlet­before­servicing.­
For­maximum­efficiency­and­trouble-free­service,­make­the­
following­periodic­maintenance,­cleaning­and­inspections.
ADJUSTING PUMP PRESSURE
Due­to­varying­fuel­viscosities­and­normal­component­wear­the­
pump­pressure­on­this­heater­may­need­to­be­adjusted.
FUEL­PRESSURE­ADJUSTMENT­SCREW
­­­­­­­­­­­­­­­­­­­­­­­­­­(located­at­the­rear­of­the­heater)
ADJUSTMENT PROCEDURE
1.­Fill­fuel­tank.
2.­Start­heater.
3.­Locate­the­pressure­adjustment­screw­and­pressure­tap,­
pictured­above,­located­on­the­back­of­the­power­pack­
assembly­and­accessible­by­the­handle­of­the­heater.
4.­Remove­and­the­rubber­cap­over­the­fuel­pressure­adjustment­
screw.
5.­Using­a­flat­bladed­screw­driver,­turn­the­pump­pressure­
adjustment­screw:
•­clockwise­ ­to­increase­pump­pressure
•­counter-clockwise­
By­using­the­installed­pressure­gauge­you­may­quantitatively­
calibrate­the­pressure.­The­manufacturer's­recommended­pump­
pressures­are­in­the­specifications­chart­on­page­3.
4
Operating Instructions and Owner's Manual
PRESSURE­GAUGE
­to­decrease­pump­pressure­­