Table des Matières
Publicité
Les langues disponibles
Les langues disponibles
2) LEARNING WITH DOUBLE BUTTON:
I.
In normal operating mode, press buttons # and
unit and generates a long beep.
II. The respective information will be shown if the control unit receives the learning data. Refer to the control unit instruction
manual to complete the learning procedure.
III. After having received the remote keypad data, the control unit will send a confirmation to the remote keypad itself. The
remote keypad will beep three times to confirm that validation was received.
Step 3:
After run the remote keypad learning procedure, set Walk Test mode on the control unit, keep the remote keypad in
the desired position and send the learning data to the control unit to check that it is within the range of the control unit
signal. To send learning data, press button
operating mode.
Step 4:
Once the correct operation of the remote keypad in the chosen position has been checked, proceed with the installation
following the procedure described below (see Mounting the remote keypad).
Step 5:
Modify the local code to access test mode, if necessary:
I. With the keypad in Test mode, press button
II. Enter 0000 (default code).
III. Press button
IV. Enter the new 4-digit code.
V. Press button #: the remote keypad will generate a long beep. The new code is enabled.
Step 6:
Press the button
M
o
u
n
t
i
n
g
t
h
e
r
e
m
o
M
o
u
n
t
i
n
g
t
h
e
r
e
m
o
To mount the remote keypad:
I. Remove the front lid.
II. Using the two assembly holes of the rear cover as a template, mark the position of the holes in the more suitable position.
III. Insert the anchor bolts if the device is fixed to plaster or bricks.
IV. Screw the remote keypad to the anchor bolts.
V. Close the front lid.
R
e
s
t
o
r
i
n
g
d
e
f
a
u
l
t
s
e
R
e
s
t
o
r
i
n
g
d
e
f
a
u
l
t
s
e
The remote keypad can be reset with the default values and restarted if the keypad code is forgotten or the remote keypad displays a
problem.
Step 1 Remove the battery.
Step 2 Hold button 3 pressed and insert the battery.
Step 3 Hold button 3 pressed until the keypad beeps 3 times.
Step 4 Release button 3: the reset procedure is done.
<
N
O
T
E
>
:
<
N
O
T
E
>
:
The keypad code returns to the default setting 0000 after resetting.
Hereby, URMET S.p.A. declares that the radio equipment type: LED REMOTE KEYPAD 1051/025 is in compliance with Directive
2014/53/EU. The full text of the EU declaration of conformity is available at the following internet address: www.urmet.com.
TO ACCESS THE PRODUCT TECHNICAL SHEET AND DOWNLOAD THE COMPLETE MANUAL CLICK ON THE
LINK OF THE URMET SITE
DIRECTIVE 2012/19/EU OF THE EUROPEAN PARLIAMENT AND OF THE COUNCIL of 4 July 2012 on waste electrical and
electronic equipment (WEEE).
The symbol of the crossed-out wheeled bin on the product or on its packaging indicates that this product must not be
disposed of with your other household waste.
Instead, it is your responsibility to dispose of your waste equipment by handing it over to a designated collection point for the
recycling of waste electrical and electronic equipment. The separate collection and recycling of your waste equipment at the time of
disposal will help to conserve natural resources and ensure that it is recycled in a manner that protects human health and the
environment.
For more information about where you can drop off your waste equipment for recycling, please contact your local city office, your
household waste disposal service or the shop where you purchased the product.
DS1051-029A
: the keypad will generate a long beep.
twice to exit Test mode and complete the installation.
t
e
k
e
y
p
a
d
t
e
k
e
y
p
a
d
t
t
i
n
g
s
t
t
i
n
g
s
SIMPLIFIED EU DECLARATION OF CONFORMITY
together. The remote keypad sends the learning command to the control
and then button 7 in Test mode or press buttons # and
and then button 6: the keypad will generate a long beep.
in normal
5
Publicité
Table des Matières
