Publicité
Les langues disponibles
Les langues disponibles
WARNING:
To reduce the risk of fire, electric shock, or injury to persons when using the washer, follow basic precautions,
including the following:
■
Read all instructions before using the washer.
■
Do not wash articles that have been previously cleaned
in, washed in, soaked in, or spotted with gasoline,
dry-cleaning solvents, other flammable, or explosive
substances as they give off vapors that could ignite or
explode.
■
Do not add gasoline, dry-cleaning solvents, or other
flammable, or explosive substances to the wash water.
These substances give off vapors that could ignite or
explode.
■
Under certain conditions, hydrogen gas may be
produced in a hot water system that has not been used
for 2 weeks or more. HYDROGEN GAS IS
EXPLOSIVE. If the hot water system has not been
used for such a period, before using the washing
machine, turn on all hot water faucets and let the water
flow from each for several minutes. This will release
any accumulated hydrogen gas. As the gas is
flammable, do not smoke or use an open flame during
this time.
Tools and Parts
Gather the required tools and parts before starting installation.
Tools needed
■
Level
■
Utility knife
■
Scissors
■
8" or 10" adjustable wrench
■
Flat-blade screwdriver
■
Pliers
■
Bucket
Parts supplied
Remove parts bag from washer. Check that all parts were
included.
■
1 hose clamp
■
2 inlet hoses
■
4 flat water hose washers
■
2 front-leveling legs with nuts
■
1 drain hose
All manuals and user guides at all-guides.com
IMPORTANT SAFETY INSTRUCTIONS
SAVE THESE INSTRUCTIONS
INSTALLATION REQUIREMENTS
■
Do not allow children to play on or in the washer. Close
supervision of children is necessary when the washer is used
near children.
■
Before the washer is removed from service or discarded,
remove the door or lid.
■
Do not reach into the washer if the drum, tub or agitator is
moving.
■
Do not install or store the washer where it will be exposed to
the weather.
■
Do not tamper with controls.
■
Do not repair or replace any part of the washer or attempt any
servicing unless specifically recommended in this manual or in
published user-repair instructions that you understand and
have the skills to carry out.
■
See "Electrical Requirements" for grounding instructions.
Location Requirements
IMPORTANT: Do not install or store the washer where it will be
exposed to the weather. Do not store or operate the washer in
temperatures at or below 32°F (0°C). Some water can remain in
the washer and can cause damage in low temperatures.
Proper installation is your responsibility.
You will need:
■
A water heater set to deliver 120°F (49°C) water to the washer.
■
A grounded electrical outlet located within 4 ft (1.2 m) of where
the power cord is attached to the back of the washer. See
"Electrical Requirements."
■
Hot and cold water faucets located within 4 ft (1.2 m) of the
back of the washer, and provide water pressure of 10-100 psi
(69-690 kPa). A pressure reduction valve should be used in
the supply line where inlet pressure entering the building
exceeds 100 psi (690 kPa) to prevent damage to the washer
mixing valve.
■
A level floor with a maximum slope of 1" (25 mm) under entire
washer.
■
A sturdy floor to support the washer weight (washer, water
and load) of 315 lbs (143 kgs).
■
A 12" (300 mm) minimum riser to provide an air cushion and
prevent noise and damage to valves for a single washer
installation.
■
A floor drain should be provided under the bulkhead.
Prefabricated bulkheads with electrical outlets, water supply
lines and drain facilities should be used only where local
codes permit.
NOTE: Front access to the pump area is available by removing
2 clips under the console area and removing the top and
cabinet assembly.
3
Publicité
