Publicité
Les langues disponibles
Les langues disponibles
Installation
Requirements
TooJs and Parts
Gather
the required
toois
and parts
before
starting
installation.
AH installations
Tools needed:
, piiers
, Phillips screwdriver
,5/16"
and 1/4" nut drivers
or hex sockets
, measuring
tape or rubr
,10" adjustabie
wrench that
opens to 1-1/8" (2,9 cm)
, fiatoNade
screwdriver
, utility knife
,2 twist-on
wire connectors
wMch are the proper size
to connect your househoH
wiring
to 16-gauge wiring
in dishwasher
, flashlight
, shallow
pan
,5/8"
open-end
wrench
, bath towel
, wood
block
Parts
needed:
,90 ° elbow
with
3/8" N.RT.
external
threads
on one
en&
(The
other
end must
fit your
water
supply
line.)
,Teflon:"
tape
or pipe
joint
compound
, shims
(if installed
with
built-up
floor)
, small
level
mnaddition,
for new installations
Tools
needed:
Parts
needed:
, electric
drill
with
1/2", 3/4"
and
1-1/2"
hole
saw
bits
, small
tubing
cutter
, wire
stripper
, ld/2"-2"
screw-type
clamp
if connecting
to waste-tee
, copper
tubing
(3/8"
recommended)
or flexible
stainless
steel
braided
fill
line
, clamp
connector
or
conduit
connector
to fit a
7/8" (2.2 cm) diameter
hole
Parts supplied
A, 2 - drain hose clamps,
1 large and 1 small
B, 2 - # 10 x 1/2" Phillips-head
screws
C, drain hose
B
C
_HE_HE_HmHE_HE_HE_mmHE_HE_HE_HmmmHE[E_HE_HmmmHE_HE_HmmmHE_HE_HmmmHE_HE_HE_HE_
Make
sure
all these
parts
are included.
See separate
parts
list for accessories
available
for your
dishwasher.
Location
Requirements
Do not run drain
lines,
water
lines
or electrical
wiring
where
they
can interfere
with
or contact
dishwasher
motor
or legs.
The location
where
the dishwasher
will
be installed
must
provide
clearance
between
motor
and flooring.
Motor
should
not touch
the floor.
Do not install
dishwasher
over
carpeted
flooring.
Protect
dishwasher
and water
lines
leading
to dishwasher
against
freezing.
Damage
from
freezing
is not covered
by
the warranty.
A side
panel
kit is available
from
your
dealer
for
installing
your
dishwasher
at the end of your
cabinetry.
A moisture
barrier
accessory
(Part No. 4396277)
is available
from
your
dealer
for
installing
underneath
the countertop,
but is not required.
Check
location
where
dishwasher
will
be instalb&The
location
must
provide:
o easy access
to water,
electricity
and drain.
o convenient
access
for loading
and unloading
dishes.
Corner
locations
require
a 2" (5.1 cm) minimum
clearance
between
the side
of the dishwasher
door
and the wall
or
cabinet.
* square
opening
for proper
operation
and appearance.
cabinet
front
perpendicular
to floor.
® level
floor.
(if floor
at front
of opening
is not level
with
floor
at rear of opening,
shims
may
be needed
to level
dishwasher.)
NOTE:To
prevent
shifting
during
dishwasher
operation,
shims
must
be securely
attached
to the floor.
if dishwasher
will
be left unused
for a period
of time
or in a
location
where
it may
be subject
to freezing,
have
it
winterized
by authorized
service
personnel.
Make
sure
pipes,
wires
and drain
hose
are within
the
shaded
area shown
in the "Cutout
dimensions"
section.
Helpful
Tip: if the floor
in the dishwasher
opening
is
uneven
(example:
fib
flooring
only
partway
into
opening)
you
will
need
to take
special
care
in
measuring
dimensions
and in leveling
dishwasher.
@Teflon is a registered trademark of E.!. Du Pont de Nemours and
Company.
3
Publicité
