Publicité
Les langues disponibles
Les langues disponibles
5. SHowily move dishwasher compHeteHy
intocabinet
opening, Donotkinkor pinch copper t ubing, d rain
hose, p ower s uppiy cordor direct w irebetween
dishwasher andcabinet.
6,
He_pfuITip:
Once the dishwasher
is in position,
you
may have to support
the front of the dishwasher
by
raising, Howering or shimming
front feet,
Remove cardboard
from under dishwasher,
NOTE:
tt is aii right
if dishwasher
fits tightly
into
cabinet
opening.
Do not remove
insuHafion
bHanket
--the
bHanket
reduces
the sound
HeveH.
LeveU the dishwasher
1. AHgn front of dishwasher
door pane[ with cabinet
doors, You may need to adjust aHignment to be even
with your cabinets,
Helpfu[Tip:
Prop up one side of frame to hoid
dishwasher
up off floor when adjusting
front [egs, With
some instaHHations, it may be easier to adjust the front
Heg using the 3/16" hex head,
2.
Check that
HeveHing Hegs are firmHy
against
the fHoor.
3.
CHose and Hatch the door,
and pHace HeveHagainst
the
front
panel
Check that
dishwasher
is piumb,
if needed,
adjust
HeveHing Heg or add shims
under
rear wheeH untiH
dishwasher
is piumb.
4. Repeat for other side of dishwasher,
NOTE: Shims must be secureiy attached to floor to prevent
their movement
when the dishwasher
is operated,
5. PHace HeveHagainst top front
opening
of tub, Check that
dishwasher
is HeveH from side to
side, If dishwasher
is not [eve[,
adjust front Hegs up or down untiH
dishwasher
is HeveH,
Make
EJectticaJ
CoRRection
Check
"EHectricaH
requirements"
section.
You need
to:
+ have the correct
eHectricaH suppHy and recommended
grounding
method.
If you
are:
+ direct
wiring,
use Option
1
+ using
a power
supply
cord,
use Option
2
Option
1, Direct wire method
1. Route direct wire so that it does not touch dishwasher
motor or Hower part of dishwasher
tub,
2. Puii direct wire through
hoie in terminai
box.
HeJpfuJ Tip:
+ SeHect the proper size twist+on
connectors
to connect your househoid
__
wiring to 16-gauge dishwasher
wiring,
+ Insert wire ends into twist+on
connector,
Do not pre-twist
bare wire,
_+,-
®Twist connector,
+ GentHy tug on wires to be sure both are
secured,
3.
Connect
the wires
as follows
using
twist+on
connectors
sized
to connect
direct
wire
to 16-gauge
dishwasher
wire:
Power supply wire:
Terminal
box wire:
vvhite_e-}_wh
ite
black_--_- black
ground
wire--ground
connector
Emectrical Shock Hazard
Electrically
ground dishwasher.
Connect
ground wire to green ground connector
in
terminal
box.
Do not use an extension
cord.
Faimure to follow these instructions
can result in death,
fire, or electrical
shock,
4. Form bare ground
wire into a U-shaped
hook. Wrap
ground
wire hook ciockwise
around
ground connector
and under the washer,
12
Publicité
