Publicité
Les langues disponibles
Les langues disponibles
If a hot surface light is ON use caution when working
around the cooktop as it is still hot.
)DVW %RLO %RRVWHU IXQFWLRQ
Once a heating element has been selected, touch the
>)$67 %2,/@ NH\ WR HQDEOHGLVDEOH WKLV IXQFWLRQ EHIRUH
or after setting the power level.
A beep sounds and the heater display shows the
selected power level and a "P" alternatively. The
"Peacock Tail" shows the selected power level.
The heater works at full power (level 9, always on) for
10 minutes. After these 10 minutes the heater returns
to the selected power level.
This option is available for all the cooking zones, both
standard, both special ones (multiple zones or bridge).
.H\ /RFN IXQFWLRQ
The key lock function is activated or deactivated holding
WKH >/2&.@ NH\ IRU VHFRQGV 7KH ORFN LQGLFDWLRQ WXUQV
RQ WKH NH\ERDUG LV ORFNHG 2I FRXUVH WKH >/2&.@ NH\
itself is always enabled.
The keys are automatically locked at start-up.
The locking function can be activated regardless of the
heaters condition (working or not). The key lock function
ORFNV DOO WKH NH\V EXW WKH >2))@ RQHV $OVR WKH JHQHUDO
>212))@ NH\ UHPDLQV DFWLYH IRU WKH RII IXQFWLRQ
6HWWLQJ WKH WLPHU
It works as a minute minder and it doesn't stop any
heating element.
The timer is available in some models only. It can be set
independently from the heating element, even if there
aren't any working zones. If the cooktop is not working,
WRXFK ¿UVW WKH PDLQ >212))@ NH\ WR HQWHU VWDQGE\
mode, with all displays showing "0".
1
Figure. 10
12
2
3
7RXFK >7@ RU >7@ NH\V WR VHW WKH WLPHU WKH LQLWLDO YDOXH
starts from "00" or "45" respectively on the timer display
(ref.1). Hold the key in order to fasten the increase/
decrease speed. The maximum value is "99".
The timer led (ref.2) indicates whether the timer is
running.
The dot in the lower right corner of the display (ref.3) is
ÀDVKLQJ ZKHQ WKH WLPHU KDV EHHQ VHOHFWHG LQ RUGHU WR
change its value. After 5 seconds since the last touch
the new value is accepted and the dot disappears.
$ EHHS FRQ¿UPV WKDW WKH QHZ YDOXH ZDV DFFHSWHG
correctly.
7R FDQFHO WKH WLPHU KROG >7@ NH\ XQWLO WKH YDOXH GHFUHDVH
WR ³´ RU WRXFK ERWK >7@ DQG >7@ VLPXOWDQHRXVO\ LQ
order to reset the value to "00" rapidly.
In some models the timer can be set in relation with a
cooking zone:
‡ 6HOHFW WKH FRRNLQJ ]RQH \RX ZDQW WR WLPH
‡ 7RXFK >7@ RU >7@ WKH WLPHU OHG UHODWHG WR WKH ]RQH
VWDUWV ÀDVKLQJ
‡ 6HW WKH WLPHU YDOXH
‡ 7KH WLPHU OHG JHWV VWHDG\ WKH YDOXH LV DFFHSWHG DQG
the countdown begins.
If more than one timer is set, the display shows the
ORZHVW YDOXH WKH RQH WKDW ZLOO H[SLUH ¿UVW 7KH WLPHU OHG
(ref.4) related to the zone which the displayed value is
UHIHUULQJ WR LV ÀDVKLQJ ,I WKH GLVSOD\HG YDOXH UHIHUV WR
WKH LQGHSHQGHQW WLPHU WKH WLPHU OHG UHI ÀDVKHV
Figure. 11
To check the remaining time for any one of the timed
]RQH WRXFK WKH >21@ NH\ UHODWHG WR WKH ]RQH WKH
FRUUHVSRQGLQJ WLPHU OHG ZLOO EHJLQ WR ÀDVK DQG WKH YDOXH
on the timer display will switch for some seconds to the
new value. After a time-out, it will switch back to the
shortest one.
To check the independent timer value when it's not
GLVSOD\HG ZLWK WKH KLJKHVW SULRULW\ WRXFK >7@ RU >7@ ZKHQ
QR ]RQHV DUH VHOHFWHG 7KH WLPHU OHG UHI ÀDVKHV DQG
the displayed value switches to the independent timer.
Use & Care Manual
ENGLISH
4
Publicité
